Correction and Materials
CORRECTION:Follow the procedures for each of the areas as required.
MATERIALS REQUIRED - FOR COWL WATER LEAKS For cowl plenum seam leaks; use *Kent SL-C (P/N 50265).
- Another method would be to make an applicator from the following products to pump sealer onto seam area within cowl.
- *3M P/N 08994 Applicator, P/N 08633 Flow Grade Resealant and a short length of rubber hose OR
- Kent P/N 9001 0 Applicator, P/N 10240 Rubber Sealer and stock P/N KA-E Extension Tube For cowl/hinge pillar leaks; Use GM P/N 12345743, 3M P/ N 08648 (or equivalent) Body Seam Sealers
* We believe these sources and their equipment to be reliable. There may be additional manufacturers of such
equipment. General Motors does not endorse, indicate any preference for or assume any responsibility for the products or equipment from these firms or for any such items which may be available from other sources.
PROCEDURE FOR COWL PLENUM SEAM (See Figure 1.)
1. Open and raise the hood to the full open position.
2. Remove the left wiper arm and blade.
3. Remove the left side cowl grille (See Figure 1, View A).
4. Using the material and equipment specified, apply sealer to the seam areas through the rectangular holes in the cowl as shown in Figure 1, Views B and C. Apply this sealer for the full length of the cowl seam from the center line of the vehicle to the left edge of the cowl plenum.
5. Allow the sealing material to dry for 15 minutes before applying second coat.
NOTE:
Allow sealer to dry completely before water testing.
6. Reinstall the left cowl grille and wiper components.
7. Torque wiper arm attachment to 23 N-m (17 lb.ft.).
PROCEDURE FOR COWL/HINGE PILLAR SEAM
(no illustration)
1. Position vehicle on hoist.
2. Open and raise hood to full open position and disconnect battery.
3. Disconnect all component attachments to the inner fender liner on the affected side of the vehicle.
4. Raise vehicle on hoist, and remove wheel and tire on the affected side of the vehicle.
5. Remove front fender wheelhouse liner to gain access to the front body hinge pillar seams.
6. Apply Body Seam Sealer to the seams.
7. Reinstall the wheelhouse liner.
8. Lower the vehicle and reinstall the components attached to the liner.
9. Reconnect the battery, lower the hood and remove vehicle from hoist.
Labor Operations and Time Allowances.
MATERIALS REQUIRED: FOR DOOR WEATHERSTRIP SEALING
Use sealer such as 3M P/N's 08302 or 08405, * Dominion/American Sure Seal P/N LSC, Kent P/N 10500 or equivalent.
IMPORTANT:
DO NOT USE BLACK type sealers that remain soft, or "uncured" for sealing door opening weatherstrips to flanges.
Repair weatherstrips and flanges by (See Figure 2).
1. Removing the windshield pillar and center pillar garnish moldings.
2. Partially remove the weatherstrip from the upper flange areas by grasping with hand and pulling. The portion of the weatherstrip on the rocker flange may be left in place.
3. If gaps at the flange joints exist (Indicated on Figure 2), apply sealer to fill the gaps at the joints.
4. Apply a continuous bead of sealer to the upper length of the weatherstrip cavity, from the front corner of the rocker area to the rear corner of the rocker area (See Figure 2, Section A-A).
5. Reinstall weatherstrip to the flange.
6. Reinstall the windshield and center pillar garnish moldings.
Labor Operations:
MATERIALS REQUIRED: FOR REAR COMPARTMENT LEAKS
- Seal seams below back glass using a sealer such as 3M P/N's 08302 or 08405, Dominion/American Sure Seal P/N LSC, Kent P/N 10500 or equivalent (See Figure 3, View A).
- For weatherstrip sealing, use the sealer listed above for the seam sealing (See Figure 3, Section A-A).
IMPORTANT:
DO NOT USE BLACK type sealers that remain soft, or "uncured" for sealing rear compartment weatherstrips to flanges.
Identification can be made by visual inspection and/or localized water test methods. In some cases, it may be necessary to inspect from inside of rear compartment while water testing with a helper.
Repair weatherstrips and flanges by (See Figure 3, Section A-A).
1. Removing weatherstrip from flange in leaking area.
2. Straightening flanges with pliers, if necessary.
3. Applying a bead of sealer into the weatherstrip cavity, using a clear type sealer as described above, for 4 to 6 inches either side of the leak area (See Figure 3, Section A-A).
4. Reinstalling the weatherstrip to the flange.
As always, water test the area after the repair, to ensure a satisfactory repair.
Labor Operation: B5410
Use Published Allowance