B257A
DTC B257A
Diagnostic Instructions
* Perform the Diagnostic System Check - Vehicle Diagnostic System Check - Vehicle prior to using this diagnostic procedure.
* Review Strategy Based Diagnosis Strategy Based Diagnosis for an overview of the diagnostic approach.
* Diagnostic Procedure Instructions Diagnostic Procedure Instructions provides an overview of each diagnostic category
DTC Descriptor
DTC B257A 00
-
Headlamp Switch Input Signal Mismatch
Diagnostic Fault Information
Circuit/System Description
The body control module (BCM) monitors three signal circuits from the headlamp switch. When the headlamp switch is in the AUTO position, all three signal circuits are open. When placed in the AUTO position, the BCM monitors inputs from the ambient light sensor to determine if headlamps are required or if daytime running lamps will be activated based on outside lighting conditions. When the headlamp switch is placed in the OFF position, the headlamp switch headlamps OFF signal circuit is grounded, indicating to the BCM that the exterior lamps should be turned OFF. With the headlamp switch in the PARK position, the headlamp switch park lamps ON signal circuit is grounded, indicating that the park lamps have been requested. When the headlamp switch is placed in the HEADLAMP position, both the headlamp switch park lamps ON signal circuit and the headlamp switch headlamps ON signal circuit are grounded. The BCM responds to the inputs by illuminating the park lamps and headlamps.
Conditions for Running the DTC
Battery voltage must be between 9-16 volts.
Conditions for Setting the DTC
* The BCM detects an open/high resistance in the headlamp switch park lamps ON signal circuit.
* The BCM detects a short to ground in the headlamp switch headlamps ON signal circuit.
* The BCM detects a short to ground in the headlamp switch headlamps OFF signal circuit.
Actions Taken When the DTC Sets
* When DTC B257A 00 is present on the headlamp switch headlamps OFF signal circuit, the low beam headlamps are always ON in the AUTO position. The headlamp switch operates in all positions other than AUTO. The AUTO headlamp defeat is inoperative.
* When DTC B257A 00 is present on the headlamp switch headlamps ON signal circuit, the low beam headlamps are always ON. The BCM disregards all headlamp switch inputs.
* When DTC B257A 00 is present on the headlamp switch park lamps ON signal circuit, the park lamps and low beam headlamps are inoperative in the PARK and HEAD positions. Headlamps and park lamps operate in AUTO position.
Conditions for Clearing the DTC
* The condition responsible for setting the DTC no longer exists.
* A history DTC will clear once 100 consecutive malfunction-free ignition cycles have occurred.
Reference Information
Schematic Reference
Headlights/Daytime Running Lights (DRL) Schematics Headlights/Daytime Running Lights (DRL) Schematics
Connector End View Reference
Component Connector End Views Fuel Pump and Level Sensor Assembly
Description and Operation
Exterior Lighting Systems Description and Operation Exterior Lighting Systems
Electrical Information Reference
* Circuit Testing Circuit Testing
* Connector Repairs Connector Repairs
* Testing for Intermittent Conditions and Poor Connections Testing for Intermittent Conditions and Poor Connections
* Wiring Repairs Wiring Repairs
Scan Tool Reference
Control Module References Control Module References for scan tool information
Circuit/System Testing
1. Ignition OFF, disconnect the harness connector at the S30 headlamp switch.
2. Ignition ON, verify the scan tool Headlamp Switch parameter is OFF.
• If not the specified value, test the signal circuit terminal 1 for short to ground. If the circuit tests normal, replace the K9 body control module.
3. Verify the scan tool Auto Headlamp Disable Switch parameter is Inactive.
• If not the specified value, test the signal circuit terminal 3 for short to ground. If the circuit tests normal, replace the K9 body control module.
4. Verify the scan tool Park Lamp Switch parameter is Off.
• If not the specified value, test the signal circuit terminal 5 for short to ground. If the circuit tests normal, replace the K9 body control module.
5. Install a 3A fused jumper wire between the signal circuit terminal 1 and ground. Verify the scan tool Headlamp Switch parameter is On.
• If not the specified value, test the signal circuit for a short to voltage or an open/high resistance. If the circuits test normal replace the K9 body control module.
6. Install a 3A fused jumper wire between the signal circuit terminal 3 and ground. Verify the scan tool Auto Headlamp Disable Switch parameter is Active.
• If not the specified value, test the signal circuit for a short to voltage or an open/high resistance. If the circuit tests normal, replace the K9 body control module.
7. Install a 3A fused jumper wire between the signal circuit terminal 5 and ground. Verify the scan tool Park Lamp Switch parameter is On.
• If not the specified value, test the signal circuit for a short to voltage or an open/high resistance. If the circuit tests normal, replace the K9 body control module.
8. If all circuits test normal, replace the S30 headlamp switch.
Repair Instructions
Perform the Diagnostic Repair Verification Verification Tests after completing the diagnostic procedure.
* Headlamp Switch Replacement Service and Repair
* Control Module References Control Module References for BCM replacement, setup, and programming