4. Camshaft Timing Chain Adjustment

Camshaft Timing Chain Adjustment

Special Tools

* EN-952 - Fixing Pin

* EN-953-A - Fixing Tool

* EN-49977-100 - Fixation Sensor Discs

For equivalent regional tools, refer to Special Tools Tools and Equipment.

1. Remove the ignition coil. Refer to Ignition Coil Replacement Service and Repair.

2. Remove the camshaft cover. Refer to Camshaft Cover Replacement Service and Repair.

3. Remove the camshaft position actuator solenoid valves. Refer to Camshaft Position Actuator Solenoid Valve Replacement Service and Repair.

4. Remove the right front wheelhouse liner. Refer to Front Wheelhouse Liner Replacement (Rear) Front Wheelhouse Liner Replacement (Front) .





5. Rotate the engine clockwise until the bore (2) in the crankshaft balancer aligns with the mark (1) on the engine front cover.





6. Remove the crankshaft bearing cap tie plate hole plug (2) and the seal ring (1).





Caution:
To ensure proper crankshaft top dead center (TDC) alignment, the retention pin should fit easily through the bore in the crankshaft tie plate and into the crankshaft. Binding of the retention pin could affect proper engine timing.

7. Install the EN-952 - fixing pin(1) to hold the crankshaft in TDC position.





8. Loosen the intake camshaft sprocket bolt (2) while holding the hexagon of the intake camshaft with a wrench (1) until the camshaft position exciter wheel is clearly rotatable.

9. Loosen the exhaust camshaft sprocket bolt while holding the hexagon of the exhaust camshaft with a wrench until the camshaft position exciter wheel is clearly rotatable.





Note:
The fixing tool should be installed completely to both camshaft grooves without high effort.

10. Adjust the camshafts so that the EN-953-A - fixing tool(1) can be installed.





11. Remove the 2 upper timing chain guide bolts (1).

12. Remove the upper timing chain guide (2).





Note:
Push the fixing tool in the direction of the arrow to ensure it engages without clearance.

13. Install the EN-49977-200 - fixing tool(2) and adjust the gearing of the fixing tool so it engages with the intake camshaft sprocket gearing (1).





14. Tighten the 2 fastening bolts (1) of the EN-49977-200 - fixing tool while pushing the fixing tool in direction of the arrow.

15. Tighten the adjuster bolt (2).





Note:
A wrong installation position is possible. Make sure that the fixation tool is installed without clearance to the cylinder head in areas (3) and (5).

16. Install the EN-49977-100 - fixation(2) to find and hold the camshaft position exciter wheels in the correct position.

17. Tighten the 2 fastening bolts (6) of the EN-49977-100 - fixation.

Caution:
Refer to Fastener Caution Fastener Caution.

18. Tighten the intake camshaft sprocket bolt (4) while holding the hexagon (1) of the intake camshaft to 50 Nm (37 lb ft).

19. Tighten the intake camshaft sprocket bolt (4) while holding the hexagon (1) of the intake camshaft an additional 60°.

20. Tighten the exhaust camshaft sprocket bolt while holding the hexagon of the exhaust camshaft to 50 Nm (37 lb ft).

21. Tighten the exhaust camshaft sprocket bolt while holding the hexagon of the exhaust camshaft an additional 60°.

22. Remove the EN-49977-100 - fixation and the EN-49977-200 - fixing tool.





23. Install the upper timing chain guide (2).

24. Install the 2 upper timing chain guide bolts (1) and tighten to 8 Nm (71 lb in).

25. Remove the EN-953-A - fixing tool.

26. Remove the EN-952 - fixing pin.

27. Rotate the crankshaft for 720° and check the engine timing again. Repeat the adjustment procedure if necessary.

28. Install the crankshaft bearing cap tie plate hole plug and seal ring and tighten to 40 Nm (30 lb ft).

29. Install the right front wheelhouse liner. Refer to Front Wheelhouse Liner Replacement (Rear) Front Wheelhouse Liner Replacement (Front)

30. Install the camshaft position actuator solenoid valves. Refer to Camshaft Position Actuator Solenoid Valve Replacement Service and Repair.

31. Install the camshaft cover. Refer to Camshaft Cover Replacement Service and Repair.

32. Install the ignition coil. Refer to Ignition Coil Replacement Service and Repair.