P0757

DTC P0757

Diagnostic Instructions

* Perform the Diagnostic System Check - Vehicle (with HP2) (Initial Inspection and Diagnostic Overview)Diagnostic System Check - Vehicle (without HP2) (Initial Inspection and Diagnostic Overview) prior to using this diagnostic procedure.
* Review Strategy Based Diagnosis (Initial Inspection and Diagnostic Overview) for an overview of the diagnostic approach.
* Diagnostic Procedure Instructions (Initial Inspection and Diagnostic Overview) provides an overview of each diagnostic category.

DTC Descriptor
DTC P0757
- Shift Solenoid (SS) 2 Valve Performance - Stuck On

Circuit/System Description

The shift solenoid (SS) valve 2 is part of the control solenoid (w/body and TCM) valve assembly and is not serviced separately. The SS valve 2 is a normally closed (NC) solenoid valve and controls fluid to the hybrid low, 1-2 clutch boost valve assembly and related clutches. During this diagnostic test, intrusive actions are taken by the transmission control module (TCM) to test the SS valve 2 to see if the valve is stuck ON. When in gear 3, gear 4, or EVT 2, if the correct gear ratio is not achieved in a predetermined period of time, the TCM commands second gear and if second gear ratio is attained this indicates a stuck ON SS valve 2 and the DTC will set.

Conditions for Running the DTC

EVT 1 or EVT 2 is commanded.

Conditions for Setting the DTC

The TCM detects shift solenoid valve 2 is ON when commanded OFF.

Action Taken When the DTC Sets

P0757 is a Type B DTC.

Conditions for Clearing the DTC

P0757 is a Type B DTC.

Diagnostic Aids

When attempting to set transmission performance DTCs, observe the Freeze Frame and Failure Records to assist in duplicating the failure conditions. Ensure the transmission fluid level is correct and there are no leaks.

Reference Information
Schematic Reference

Automatic Transmission Controls Schematics (Electrical Diagrams)
Connector End View Reference

Component Connector End Views (Connector Views)
Electrical Information Reference

* Circuit Testing (Component Tests and General Diagnostics)
* Connector Repairs (Component Tests and General Diagnostics)
* Testing for Intermittent Conditions and Poor Connections (Component Tests and General Diagnostics)
* Wiring Repairs (Component Tests and General Diagnostics)

DTC Type Reference

Powertrain Diagnostic Trouble Code (DTC) Type Definitions (Diagnostic Trouble Code Descriptions)
Scan Tool Reference

Control Module References (Programming and Relearning) for scan tool information.
Special Tools

DT-47825 Control Solenoid Test Plate Kit

Circuit/System Verification

1. Verify that DTCs P0721, P0722, P0723, P0966, P0967, P0969, P0970, P0971, P0973, P0974, P0976, P0977, P2720, P2721, P2728, P2729, or P2730 are not set.

• If any of the DTCs are set, refer to Diagnostic Trouble Code (DTC) List - Vehicle (Diagnostic Trouble Code Descriptions).

2. Perform the Transmission Fluid Check (Transmission Fluid Check).
3. Operate the vehicle in drive to obtain 56 km/h (35 mph), stop the vehicle, turn the ignition Off for at least 30 seconds. Perform this 2 times.

• If the DTC resets, refer to Circuit/System Testing.

Circuit/System Testing

1. Perform the Line Pressure Check (Line Pressure Check).

• If the pressure is out of specification correct that concern first.

2. Perform the Control Solenoid Valve and Transmission Control Module Assembly Inspection (Control Solenoid Valve and TCM Assembly Solenoid Performance Test).

• If a concern is found, repair or replace the control solenoid (w/body and TCM) valve assembly.

3. Perform the Control Solenoid Valve and Transmission Control Module Assembly Solenoid Performance Test (Control Solenoid Valve and TCM Assembly Solenoid Performance Test).

• If the solenoid is found to be leaking or stuck OFF, replace the control solenoid (w/body and TCM) valve assembly.

• If the control solenoid (w/body and TCM) valve assembly tests normal, inspect the valve body and hydraulic circuits for a leak or a stuck valve.

Repair Instructions

Perform the Diagnostic Repair Verification (Verification Tests) after completing the diagnostic procedure.

Control Module References (Programming and Relearning) for control solenoid (w/body and TCM) valve assembly replacement, setup, and programming.