P07A5
DTC P07A5
Diagnostic Instructions
* Perform the Diagnostic System Check - Vehicle (with HP2) (Initial Inspection and Diagnostic Overview)Diagnostic System Check - Vehicle (without HP2) (Initial Inspection and Diagnostic Overview) prior to using this diagnostic procedure.
* Review Strategy Based Diagnosis (Initial Inspection and Diagnostic Overview) for an overview of the diagnostic approach.
* Diagnostic Procedure Instructions (Initial Inspection and Diagnostic Overview) provides an overview of each diagnostic category.
DTC Descriptor
DTC P07A5
- Transmission Friction Element 2 Stuck On
Typical Scan Tool Data
Circuit/System Description
The hybrid powertrain control module (HPCM) monitors the Clutch Slip parameters for each Hybrid Trans. Mode Commanded state. This DTC detects no clutch slip when the hybrid direct, 2-3-4 clutch is commanded OFF, indicating a stuck or welded clutch condition.
Conditions for Running the DTC
* Hybrid direct, 2-3-4 clutch is the primary off-going clutch.
* The Calc. Trans Input Speed is greater than 250 RPM.
Conditions for Setting the DTC
The hybrid direct, 2-3-4 clutch is commanded OFF for 3 seconds and the HPCM detects the hybrid direct, 2-3-4 clutch slip speed is less than 1000 RPM for 3 seconds, when commanded OFF.
Action Taken When the DTC Sets
P07A5 is a Type B DTC.
Conditions for Clearing the DTC
P07A5 is a Type B DTC.
Diagnostic Aids
When attempting to set transmission performance DTCs, observe the Freeze Frame and Failure Records to assist in duplicating the failure conditions. Ensure the transmission fluid level is correct and there are no leaks. If there are any other transmission DTCs set, diagnose those first.
Reference Information
Schematic Reference
Automatic Transmission Controls Schematics (Electrical Diagrams)
Connector End View Reference
Component Connector End Views (Connector Views)
Electrical Information Reference
* Circuit Testing (Component Tests and General Diagnostics)
* Connector Repairs (Component Tests and General Diagnostics)
* Testing for Intermittent Conditions and Poor Connections (Component Tests and General Diagnostics)
* Wiring Repairs (Component Tests and General Diagnostics)
DTC Type Reference
Powertrain Diagnostic Trouble Code (DTC) Type Definitions (Diagnostic Trouble Code Descriptions)
Scan Tool Reference
Control Module References (Programming and Relearning) for scan tool information.
Circuit/System Verification
1. Clear the DTC.
2. Operate the vehicle from 1st through 4th gear while observing the Direct 2-3-4 Clutch Slip parameter. Stop the vehicle and turn the ignition OFF for 30 seconds. Perform this action 2 times. The Direct 2-3-4 Clutch Slip parameter should display greater than 0 RPM when the Direct 2-3-4 Clutch Status parameter displays Released.
• If any other transmission DTCs are set, diagnose those first.
• If the DTC P07A5 resets, go to Component Testing.
Component Testing
1. Perform the Line Pressure Check (Line Pressure Check).
• If you found a concern, repair the concern.
2. Perform the Control Solenoid Valve and Transmission Control Module Assembly Solenoid Performance Test (Control Solenoid Valve and TCM Assembly Solenoid Performance Test).
• If a concern is found, replace the control solenoid (w/body and TCM) valve assembly.
3. Inspect the hybrid direct, 2-3-4 clutch regulator valve for sticking or damage.
• If you found a concern with the hybrid direct, 2-3-4 clutch regulator valve, repair or replace the valve or valve body.
4. Inspect the hybrid direct, 2-3-4 clutch for a stuck On or damaged condition.
• If you found a hybrid direct, 2-3-4 clutch concern, repair or replace the hybrid direct, 2-3-4 clutch assembly as necessary.
Repair Instructions
Perform the Diagnostic Repair Verification (Verification Tests) after completing the diagnostic procedure.
* Control Module References (Programming and Relearning) for control solenoid (w/body and TCM) valve assembly replacement, setup, and programming.
* Hybrid Direct, 2-3-4 Clutch Housing Overhaul (Overhaul) for hybrid direct, 2-3-4 clutch replacement or overhaul.
* Control Solenoid Valve and Transmission Control Module Assembly Replacement (Control Solenoid Valve and Transmission Control Module Assembly Replacement) for lower valve body assembly replacement.
* Perform the valve body inspection procedure, refer to Control Solenoid Valve and Transmission Control Module Assembly Inspection (Control Solenoid Valve and TCM Assembly Solenoid Performance Test). If the inspection procedure indicates to replace the valve body, refer to Control Solenoid Valve and Transmission Control Module Assembly Replacement (Control Solenoid Valve and Transmission Control Module Assembly Replacement) and Control Valve Upper Body Replacement (Service and Repair).