Seat Belt Systems: Description and Operation
SAFETY BELT SYSTEMWARNING: After any crash, all of the following safety belt assemblies and attaching hardware must be inspected by an authorized dealer to verify correct function:
- Retractors
- Buckles
- Belt tension sensor (BTS) (if equipped)
- Front safety belt buckle support assemblies (slide bar) (if equipped)
- Safety belt shoulder belt height adjusters (if equipped)
- Child safety seat tether bracket assemblies
- Automatic locking retractor (ALR) feature for child safety seats (passenger seating positions only)
If any safety belt assembly is damaged, does not operate correctly or does not pass all of the Functional Tests in the Diagnosis and Testing portion, a new safety belt assembly must be installed. If any safety belt assembly attaching areas are damaged or distorted, the sheet metal must be restored to its original structural integrity and new safety belt assembly and attaching hardware must be installed. Failure to install new safety belt assemblies and attaching hardware may increase the risk of serious personal injury or death in a crash.
After any crash that results in deployment of the driver and/or front outboard passenger safety belt pretensioners, new driver and/or front outboard passenger safety belt systems (including retractors, buckles and height adjusters) must be installed. Failure to install new safety belt systems increases the risk of serious personal injury or death in a crash.
When replacing any active occupant restraint components, use only the replacement parts specified in the Ford Customer Service Division Master Parts Catalog.
The active restraint system consists of the following:
- Front row safety belt buckles, attached to the inboard side of the seats
- Front row safety belt retractors and pretensioners, located behind the lower B-pillar trim panels
- Second row outboard safety belt retractors, located behind the rear quarter trim panels
- Second row 60/40 seat center safety belt retractor and LH safety belt buckle assembly is integrated into the 60 percent seat back
- Second row dual safety belt buckle assembly for the 60/40 seat attached to the 60/40 seat
- Second row lower anchors and tethers for children (LATCH) at all outboard rear seating positions, welded to the seat backrest frame
- Child safety seat tether anchors attached to the back of the rear seat
Safety Belt Retractor And Pretensioner
The front safety belt retractors use a safety belt pretensioner system. The pretensioner is a pyrotechnic device that removes excess webbing slack from the safety belt. The pretensioners are activated when the restraints control module (RCM) detects an impact force exceeding a programmed limit and deployment is required.
For safety belt retractor pretensioner diagnostic information or disposal information, refer to Air Bag Systems.
Dual Locking Mode Retractors
NOTE: When installing a new dual locking mode retractor, the retractor should be checked to make sure it is not in the automatic locking retractor (ALR) mode after installation in the stowed position.
All outboard continuous-loop, 3-point retractor systems, except the driver position, are equipped with the dual locking mode system.
The emergency locking retractor (ELR) mode will allow the occupant freedom of movement, locking tight only on hard braking, hard cornering, or an impact of approximately 8 km/h (5 mph). The ELR mode helps to reduce the forward movement of the driver and passengers. The ELR mode is continuously in operation at all seating positions.
The ALR portion of this system does not allow the occupant freedom of movement. The ALR mode is used when locking a child seat in an outboard seating position or when a tight belt fit is desired. The ALR mode is disengaged when the webbing is free to move in or out of the retractor. The ALR mode is automatically engaged when the webbing is fully extracted from the retractor and then allowed to retract. As the webbing is retracted back onto the spool, an audible clicking sound is made, indicating that the retractor is in ALR mode. The ALR mode is automatically disengaged when most of the webbing is retracted back onto the spool.
The automatic locking mode must be used when installing a child safety seat in the front or rear passenger seating positions where dual locking mode retractors are provided.
Energy Management Retractor
This vehicle has a safety belt system with an energy management feature at the front seating positions to help further reduce the risk of injury in the event of a head-on collision.
The energy management retractor feature is designed to pay out webbing in a controlled manner. This feature is designed to help reduce the belt force acting on an occupant's chest.
Rear Safety Belt Buckle
The 40 percent and/or 60 percent rear safety belt buckles are mounted to the seat backrest frames on the 40 and 60 percent seats. The LH safety belt buckle on the rear 60 percent seat is serviced as part of the center safety belt retractor. To service the LH safety belt buckle, refer to Safety Belt Retractor - Rear, Center.
Child Safety Seat Tether Anchors
WARNING: Always tighten the child safety seat tether anchor/bolt to specification. Failure to follow this instruction may result in the child's safety seat being incorrectly secured, which increases the risk of serious personal injury or death to the child in a sudden stop or crash.
If the child safety seat tether anchors were in use during a collision, inspect and install new anchors as necessary. Return the vehicle structure to its original production configuration.
Lower Anchors and Tethers for Children (LATCH)
The child safety seat lower anchor and tethers for children (LATCH) system is a standardized and uniform attachment system for installing child safety seats in passenger vehicles. LATCH-equipped child safety seats have 2 lower attachments that connect to the vehicle portion of the LATCH system.
The vehicle portion of the system consists of 2 attachment points (6-mm wires) welded to the 60 percent and the 40 percent rear seat backrest frame. The attachment points protrude from the biteline between the seat cushion and seat backrest.
If a child safety seat was in use during a collision, inspect the vehicle portion of the system for damage. If any of the attachment points (6-mm wires) are damaged, install a new seat backrest frame.
Safety Belt Warning Indicator and Chime
The warning indicator and chime are reminders to fasten the safety belt. The system operates as follows:
- If the driver's safety belt is not buckled before the ignition switch is turned to the ON position, the safety belt warning indicator illuminates 1-2 minutes and the warning chime sounds 4-8 seconds.
- If the driver's safety belt is buckled while the indicator is illuminated and the warning chime is sounding, the safety belt warning indicator and warning chime will turn off.
- If the driver's safety belt is buckled before the ignition switch is turned to the ON position, the safety belt warning indicator and chime will remain off.
Belt-Minder(R)
The Belt-Minder(R) feature is a supplemental warning to the safety belt warning function. This feature provides an additional reminder that the front safety belts are unbuckled by intermittently sounding a chime and illuminating the safety belt warning indicator in the instrument cluster (IC) module.
Both the driver and passenger safety belts are monitored and either may activate the Belt-Minder(R) feature. The warnings are the same for the driver and the front passenger. If the Belt-Minder(R) warnings have expired (warnings for approximately 5 minutes) for one occupant (driver or front passenger), the other occupant can still activate the Belt-Minder(R) feature.
The Belt-Minder(R) feature uses information from the occupant classification sensor (OCS) system on the front passenger seat to determine if a front seat passenger is present and therefore potentially in need of a warning. The warning is activated if the OCS system senses weight exceeding a programmed set point.
The Belt-Minder(R) feature can be enabled/disabled using a scan tool. When enabled, the feature becomes a user accessible item on the message center allowing the user to turn the feature on and off. To activate or deactivate the Belt-Minder(R) feature, refer to Instrument Panel, Gauges and Warning Indicators or the Owner's Literature.
