Engine Control Module: Service and Repair
ECM/PCM ReplacementSpecial Tools Required
- Honda diagnostic system (HDS) tablet tester
- Honda interface module (HIM) and an iN workstation with HDS and CM update software
- HDS pocket tester
- GNA-600 and an iN workstation with HDS and CM update software
NOTE:
- Make sure the HDS is loaded with the latest software version.
- If you are replacing the ECM/PCM after substituting a known-good ECM/PCM, reinstall the original ECM/PCM, then do this procedure.
- During the procedure, is any READ DATA, WRITE DATA, or other data checks fail, note the failure, then continue.
1. Make sure you have the anti-theft code for the audio system or the navigation system (if equipped), then write down the audio presets.
2. Connect the HDS to the data link connector (DLC) (A) located under the driver's side of the dashboard.
3. Turn the ignition switch ON (II).
4. Make sure the HDS communicates with the ECM/PCM and other vehicle systems. If it doesn't, go to the DLC circuit troubleshooting. Testing and Inspection If you are returning from DLC circuit troubleshooting, skip steps 5 through 10,19 through 24, and 27 through 29, and do these procedures after replacing the ECM/PCM (USA, Canada models):
- Replace the engine oil and the engine oil filter.
- Replace the ATF (A/T model).
- Clean the throttle body.
5. USA, Canada models: Select the PGM-FI system with the HDS.
6. USA, Canada models: Select the INSPECTION MENU with the HDS.
7. USA, Canada models: Select the ETCS TEST, then select the TP POSITION CHECK, and follow the screen prompts.
NOTE: If the TP POSITION CHECK indicates FAILED, continue with this procedure.
8. USA, Canada models: Select the REPLACE ECM/PCM MENU, then READ DATA, and follow the screen prompts.
NOTE:
- Doing this step copies (READS) the engine oil life data from the original ECM/PCM so you can later download (WRITES) it into the new ECM/PCM.
- If READ DATA indicates FAILED, continue with this procedure.
9. USA, Canada models A/T: Select the A/T system with the HDS.
10. USA, Canada models A/T: Select the REPLACE TCM/PCM MENU, then READ DATA, and follow the screen prompts.
NOTE:
- Doing this step copies (READS) the ATF life data from the original PCM so you can later download (WRITES) it into the new PCM.
- If READ DATA indicates FAILED, continue with this procedure.
11. Turn the ignition switch OFF.
12. Remove the battery.
13. Remove the cover (A).
14. Remove the bolts (D), then remove the ECM/PCM (E).
15. Disconnect ECM/PCM connectors A, B, and C.
NOTE: ECM/PCM connectors A, B, and C have symbols (A=Square, B=triangle, C=circle) embossed on them for identification.
16. Install the ECM/PCM and the battery in the reverse order of removal.
17. Turn the ignition switch ON (II).
18. USA, Canada models: Manually input the VIN to the ECM/PCM with the HDS:
NOTE: DTC P0630 "VIN Not Programmed or Mismatch" may be stored because the VIN has not been programmed into the ECM/PCM; ignore it, and continue this procedure.
19. USA, Canada models: If the READ DATA (engine oil life) failed in step 8, go to step 22 (A/T model) or step 25 (M/T model). Otherwise, go to step 20.
20. USA, Canada models: Select the PGM-FI system with the HDS.
21. USA, Canada models: Select the REPLACE ECM/PCM MENU, then WRITE DATA, and follow the screen prompts.
NOTE: If the WRITE DATA indicates FAILED, continue with this procedure.
22. USA, Canada models A/T: If the READ DATA (ATF life) failed in step 10, go to step 25. Otherwise go to step 23.
23. USA, Canada models A/T: Select the A/T SYSTEM with the HDS.
24. USA, Canada models A/T: Select the REPLACE TCM/PCM MENU, then WRITE DATA, and follow the screen prompts.
NOTE: If the WRITE DATA indicates FAILED, continue with this procedure.
25. Select IMMOBI system with the HDS.
26. Enter the immobilizer code with the ECM/PCM replacement procedure in the HDS; it allows you to start the engine.
27. USA, Canada models: If the TP POSITION CHECK failed in step 7 clean the throttle body, then go to step 28.
28. USA, Canada models: If the READ DATA failed in step 8 or the WRITE DATA failed in step 21, replace the engine oil and engine oil filter, then go to step 29 (A/T model) or step 30 (M/T model).
29. USA, Canada models: If the READ DATA failed in step 10 or the WRITE DATA failed in step 24, replace the ATF, then go to step 30.
30. Select PGM-FI system, and reset the ECM/PCM with the HDS.
31. Update the ECM/PCM if it does not have the latest software.
32. Do the ECM/PCM idle learn procedure.
33. Do the CKP pattern learn procedure.
34. Enter the anti-theft code for the audio or the navigation system (if equipped), then set the clock (if needed).