Manual Transmission Removal

Manual Transmission Removal

SRS components are located in this area. Review the SRS component locations: '00-05 models, '06-09 models, Locations and the precaution and procedures Technician Safety Information before doing repair or service.

NOTE: Use fender covers to avoid damaging painted surfaces.

1. Do the battery removal procedure. Removal and Replacement

2. Loosen the locknut (A), then remove the shift lever knob (B).

3. Remove the center console. Center Console Removal/Installation

Except CR model





CR model





4. Remove the boot holder (A) by releasing the lock tabs (B) indicated by the arrowheads (C). Insert a hook-shaped tool (D) underneath the boot holder, and lift slightly while releasing the lock tabs using a flat-tip screwdriver (E).

5. Pull up and remove the boot holder and the shift lever boot (F).






6. Remove the three bolts, then remove the shift lever (A) and the shift lever spring (B).






7. '00-05 models: Disconnect the air hose (A) and the breather pipe (B), then remove the air cleaner housing cover (C) and the air cleaner element assembly (D).






8. '00-05 models: Disconnect the air control valve vacuum control solenoid valve connector (A) and the vacuum hoses (B), then remove the air cleaner housing (C).






9. '06-09 models: Disconnect the intake air temperature (IAT) sensor connector (A) and the breather pipe (B), remove the manifold absolute pressure (MAP) sensor harness (C) from the holder, then remove the air cleaner housing cover (D) and the air cleaner element assembly (E).






10. '06-09 models: Remove the IAT sensor harness clamps (A), then remove the air cleaner housing (B).






11. Turn the steering wheel to the straight-ahead position, then remove the key from the ignition switch, and lock the steering column. Make reference marks (A) across the steering joint (B).

12. Loosen the upper steering joint bolt (C), and remove the lower steering joint bolt (D) with the washer (E). Disconnect the steering joint from the gear box.

13. Remove the drive belt and the alternator. Removal and Replacement






14. Disconnect the 1P connector (A), then remove the four mounting bolts and the A/C compressor (B). Hang the A/C compressor from the body with a piece of wire.






15. Remove the four exhaust manifold cover mounting bolts.






16. Remove the heat shield (A), then remove the exhaust manifold cover.






17. '00-05 models: Remove the upper starter motor mounting bolt (A) and the upper intake manifold bracket mounting bolt (B). Disconnect the hose (C) from the suction valve.






18. '06-09 models: Remove the upper starter motor mounting bolt (A) and the upper intake manifold bracket mounting bolt (B).






19. '00-05 models: Disconnect the camshaft position (CMP) sensor A (top dead center (TDC) sensor 1) and CMP sensor B (TDC sensor 2) connectors.






20. '06-09 models: Disconnect the camshaft position (CMP) sensor connector (A).






21. Disconnect the 2P connector (A) from the steering gearbox (B).

22. Disconnect the torque sensor 3P connector (C), and remove the wire harness clamp (D).

23. Raise the vehicle on a lift.






24. Remove the splash shield.

25. Drain the MTF. Reinstall the drain plug with a new sealing washer. MTF Inspection and Replacement






26. Remove the wire harness (A), the ground cable (B), and the lower intake manifold bracket mounting bolt, then remove the intake manifold bracket (C).






27. Disconnect the primary heated oxygen sensor (primary HO2S) (sensor 1) ('00-05 models) or the air fuel ratio (A/F) sensor (sensor 1) ('06-09 models) (A), the secondary heated oxygen sensor (secondary HO2S) (sensor 2) (B), and the back-up light switch (C) connectors, then remove the wire harness from the transmission.






28. Remove the three way catalytic converter (TWC) (A) and the gaskets (B).






29. Remove the exhaust manifold bracket (A) and the exhaust manifold (B).

30. Remove the propeller shaft. Propeller Shaft Removal






31. Remove the four shift boot holder mounting bolts.






32. Remove the release fork boot (A), then carefully move the slave cylinder (B). Do not press the clutch pedal after the slave cylinder has been removed.

'00-03 models





'04-09 models





33. Pull out the release fork (A) from the release fork hanger. Wedge a shop towel (B) between the opening in the clutch housing and the release fork to hold the release fork in place.






34. Remove the five lower transmission mounting bolts.






35. Place a transmission jack (A) under the front subframe and the engine mounting stiffener.

36. Remove the two center mounting bolts (B).

37. Loosen the four front subframe mounting bolts 75 mm (3.0 in.) as shown.

38. Lower the front subframe in until it touches the four loosened mounting bolts.






39. Support the transmission with a transmission jack, and remove the transmission rear mount (A).






40. Lower the transmission. Disconnect the vehicle speed sensor (VSS) ('00-05 models) or the output shaft (countershaft) speed sensor ('06-09 models) connector (A), then remove the wire harness (B) from the transmission.






41. Remove the three upper transmission mounting bolts.

42. Pull the transmission away from the engine until it clears the mainshaft.

43. Slowly lower the transmission about 150 mm (6 in.). Check once again that all hoses and harnesses are disconnected and free from the transmission, then lower it completely.






44. Remove the transmission rear mount (A) from the transmission.