DTC Troubleshooting
DTC Troubleshooting: P0848
DTC P0848:
Open in Transmission Fluid Pressure Switch B (3rd Clutch) Circuit, or Transmission Fluid Pressure Switch B (3rd Clutch) Stuck OFF
NOTE: Before you troubleshoot, record all freeze data and any on-board snapshot with the HDS, and review General Troubleshooting Information Reading and Clearing Diagnostic Trouble Codes.
1. Turn the ignition switch to ON (II).
2. Clear the DTC with the HDS.
3. Start the engine, and warm it up to normal operating temperature (the radiator fan comes on).
4. Test-drive the vehicle in 3rd gear with the shift lever in D3, and check if the Shift Control indicates 3 with the HDS in the A/T Data List.
5. Check the 3rd Pressure Switch with the HDS in the A/T Data List.
Is the 3rd Pressure Switch ON?
YES -
Go to step 6.
NO -
Go to step 8.
6. Test-drive the vehicle in 3rd gear with the shift lever in D, for at least 2 seconds.
7. Monitor the OBD STATUS for P0848 in the DTCs MENU with the HDS.
Does the HDS indicate FAILED?
YES -
Go to step 8.
NO -
If the HDS indicates PASSED, intermittent failure, the system is OK at this time. Check for poor connections or loose terminals between transmission fluid pressure switch B (3rd clutch) and the PCM. If the HDS indicates NOT COMPLETED, go to step 6.
8. Turn the ignition switch to LOCK (0).
9. Disconnect the transmission fluid pressure switch B (3rd clutch) connector.
10. Turn the ignition switch to ON (II).
11. Measure the voltage between the transmission fluid pressure switch B (3rd clutch) connector terminal and body ground.
Is there about 5 V?
YES -
Replace transmission fluid pressure switch B (3rd clutch), then go to step 16.
NO -
Go to step 12.
12. Turn the ignition switch to LOCK (0).
13. Jump the SCS line with the HDS.
14. Disconnect PCM connector B (44P).
15. Check for continuity between PCM connector terminal B9 and the transmission fluid pressure switch B (3rd clutch) connector terminal.
Is there continuity?
YES -
Go to step 23.
NO -
Repair an open in the wire between PCM connector terminal B9 and transmission fluid pressure switch B (3rd clutch), then go to step 16.
16. Reconnect all connectors.
17. Turn the ignition switch to ON (II).
18. Clear the DTC with the HDS.
19. Start the engine, and warm it up to normal operating temperature (the radiator fan comes on).
20. Test-drive the vehicle in 3rd and 4th gears, with the shift lever in D, for at least 2 seconds in each gear.
21. Check for Pending or Confirmed DTCs with the HDS.
Is DTC P0848 indicated?
YES -
Check for poor connections or loose terminals between transmission fluid pressure switch B (3rd clutch) and the PCM, then go to step 1.
NO -
Go to step 22.
22. Monitor the OBD STATUS for P0848 in the DTCs MENU with the HDS.
Does the HDS indicate PASSED?
YES -
Troubleshooting is complete. If any other Pending or Confirmed DTCs were indicated in step 21, go to the indicated DTC's troubleshooting.�
NO -
If the HDS indicates FAILED, check for poor connections or loose terminals between transmission fluid pressure switch B (3rd clutch) and the PCM, then go to step 1. If the HDS indicates NOT COMPLETED, go to step 19.
23. Reconnect all connectors.
24. Update the PCM if it does not have the latest software ECM/PCM Update, or substitute a known-good PCM.
25. Start the engine, and warm it up to normal operating temperature (the radiator fan comes on).
26. Test-drive the vehicle in 3rd and 4th gears, with the shift lever in D, for at least 2 seconds in each gear.
27. Check for Pending or Confirmed DTCs with the HDS.
Is DTC P0848 indicated?
YES -
Check for poor connections or loose terminals between transmission fluid pressure switch B (3rd clutch) and the PCM. If the PCM was updated, substitute a known-good PCM, then go to step 25. If the PCM was substituted, go to step 1.
NO -
Go to step 28.
28. Monitor the OBD STATUS for P0848 in the DTCs MENU with the HDS.
Does the HDS indicate PASSED?
YES -
If the PCM was updated, troubleshooting is complete. If the PCM was substituted, replace the original PCM Service and Repair. If any other Pending or Confirmed DTCs were indicated in step 27, go to the indicated DTC's troubleshooting.�
NO -
If the HDS indicates FAILED, check for poor connections or loose terminals between transmission fluid pressure switch B (3rd clutch) and the PCM. If the PCM was updated, substitute a known-good PCM, then go to step 25. If the PCM was substituted, go to step 1. If the HDS indicates NOT COMPLETED, go to step 25.