DTC Troubleshooting
DTC Troubleshooting: P0848 (26)
DTC P0848:
Transmission Fluid Pressure Switch B (3rd Clutch) (Open or Stuck OFF)
NOTE:
- Before you troubleshoot, record all freeze data and any on-board snapshot with the HDS, and review the General Troubleshooting Information How To Troubleshoot The A/T System.
- Some wire colors vary according to the model year, and are indicated with an asterisk as follows:
- *(1): '09 - 10 models
1. Clear the DTC with the HDS.
2. Start the engine, and warm it up to normal operating temperature (the radiator fan comes on).
3. Verify Shift Control display in the HDS while driving in 3rd gear:
- Seven-position transmission: Drive the vehicle in 3rd gear in D3, and verify with the HDS in the A/T data list that the Shift Control indicates 3rd.
- Five-position transmission: Drive the vehicle in 3rd gear in the sequential sport shift mode in S, and verify with the HDS in the A/T data list that the Shift Control indicates 3rd.
4. Check the 3rd Pressure Switch signal with the HDS in the A/T data list.
Is the 3rd Pressure Switch ON?
YES -
Go to step 5.
NO -
Go to step 7.
5. Test-drive the vehicle:
- Seven-position transmission: Drive the vehicle in 3rd gear in D3 for at least 2 seconds, then slow down to a stop.
- Five-position transmission: Drive the vehicle in 3rd gear in the sequential sport shift mode in S for at least 2 seconds, then slow down to a stop.
6. Monitor the OBD status for P0848 in the DTCs/Freeze Data in A/T Mode Menu for a pass/fail.
Does the HDS indicate FAILED?
YES -
Go to step 7.
NO -
Intermittent failure, the system is OK at this time. Check for poor connections or loose terminals at the transmission fluid pressure switch B (3rd clutch) and the PCM. If the HDS indicates NOT COMPLETED, return to step 5 and recheck.
7. Measure the 3rd clutch pressure A/T Pressure Test.
Is the 3rd clutch pressure within the service limits?
YES -
Go to step 8.
NO -
Repair shift valves A, B, and C, and related hydraulic circuit, or replace the transmission, then go to step 22.
8. Turn the ignition switch to LOCK (0).
9. Disconnect the transmission fluid pressure switch B (3rd clutch) connector.
10. Turn the ignition switch to ON (II).
11. Measure the voltage between the transmission fluid pressure switch B (3rd clutch) connector terminal and body ground.
Is there about 5 V?
YES -
Replace the transmission fluid pressure switch B (3rd clutch) Transmission Fluid Pressure Switch A (2ND Clutch) Replacement, then go to step 22.
NO -
Go to step 12.
12. Turn the ignition switch to LOCK (0).
13. Jump the SCS line with the HDS.
14. Disconnect PCM connector B (49P).
15. Check for continuity between PCM connector terminal B9 and the transmission fluid pressure switch B (3rd clutch) connector terminal.
Is there continuity?
YES -
Go to step 16.
NO -
Repair an open in the wire between PCM connector terminal B9 and the transmission fluid pressure switch B (3rd clutch), then go to step 22.
16. Reconnect all connectors.
17. Update the A/T software in the PCM if it does not have the latest software ECM/PCM Update, or substitute a known-good PCM.
18. Start the engine, and warm it up to normal operating temperature (the radiator fan comes on).
19. Test-drive the vehicle:
- Seven-position transmission: Drive the vehicle in 3rd gear in D for at least 2 seconds, then press the accelerator pedal so that the transmission upshifts into 4th gear, and drive in 4th gear for at least 2 seconds. Slow down and stop the engine.
- Five-position transmission: Drive the vehicle in 3rd gear in the sequential sport shift mode in S for at least 2 seconds, then upshift to 4th gear by pulling the paddle shifter + (upshift switch), and drive in 4th gear for at least 2 seconds. Slow down and stop the engine.
20. Check for Pending or Confirmed DTCs with the HDS.
Is DTC P0848 indicated?
YES -
If the PCM was updated, substitute a known-good PCM, then recheck. If the PCM was substituted, go to step 1.
NO -
Go to step 21.
21. Monitor the OBD status for P0848 in the DTCs/Freeze Data in A/T Mode Menu for a pass/fail.
Does the HDS indicate PASSED?
YES -
If the PCM was updated, troubleshooting is complete. If the PCM was substituted, replace the original PCM Service and Repair. If any other DTCs were indicated on step 20, go to the indicated DTC's troubleshooting.
NO -
Check for poor connections and loose terminals at the transmission fluid pressure switch B (3rd clutch) and the PCM. If the PCM was updated, substitute a known-good PCM, then recheck. If the PCM was substituted, go to step 1. If the HDS indicates NOT COMPLETED, return to step 19 and recheck.
22. Reconnect all connectors.
23. Clear the DTC with the HDS.
24. Start the engine, and warm it up to normal operating temperature (the radiator fan comes on).
25. Test-drive the vehicle:
- Seven-position transmission: Drive the vehicle in 3rd gear in D for at least 2 seconds, then press the accelerator pedal so that the transmission upshifts into 4th gear, and drive in 4th gear for at least 2 seconds. Slow down and stop the engine.
- Five-position transmission: Drive the vehicle in 3rd gear in the sequential sport shift mode in S for at least 2 seconds, then upshift to 4th gear by pulling the paddle shifter + (upshift switch), and drive in 4th gear for at least 2 seconds. Slow down and stop the engine.
26. Check for Pending or Confirmed DTCs with the HDS.
Is DTC P0848 indicated?
YES -
Check for poor connections and loose terminals at the transmission fluid pressure switch B (3rd clutch) and the PCM, then go to step 1.
NO -
Go to step 27.
27. Monitor the OBD status for P0848 in the DTCs/Freeze Data in A/T Mode Menu for a pass/fail.
Does the HDS indicate PASSED?
YES -
Troubleshooting is complete. If any other DTCs were indicated on step 26, go to the indicated DTC's troubleshooting.
NO -
Check for poor connections and loose terminals at the transmission fluid pressure switch B (3rd clutch) and the PCM, then go to step 1. If the HDS indicates NOT COMPLETED, return to step 25 and recheck.