B1702
DTC B1701 BUCKLE PRETENSIONER [DRIVER] RESISTANCE TOO HIGHDTC B1702 BUCKLE PRETENSIONER [DRIVER] RESISTANCE TOO LOW
DTC B1706 BUCKLE PRETENSIONER [PASSENGER] RESISTANCE TOO HIGH
DTC B1707 BUCKLE PRETENSIONER [PASSENGER] RESISTANCE TOO LOW
DTC DESCRIPTION
The Buckle Pretensioner circuit consists of the SRSCM and two Buckle Pretensioners (BUPT). The SRSCM sets above DTC(s) if it detects that the resistance of BUPT squib is too high or low.
DTC Detecting Condition:
Schematic Diagram:
SPECIFICATION BUPT
resistance : 1.5 - 5.7 ohms
TERMINAL & CONNECTOR INSPECTION
1. Visually inspect all connectors related to the affected circuit for damage and secure connection.
2. Inspect terminals for damage and corrosion.
CAUTION: Avoid damaging connectors during the inspection process.
3. Are any problems found?
NO - Go to next step (INSPECTION PROCEDURE).
YES - After repairing the trouble part, check whether DTC occurs or not.
INSPECTION PROCEDURE
1. PREPARATION
1. Turn the ignition switch to LOCK.
2. Disconnect the battery negative cable from the battery and wait for at least 3 minutes.
3. Remove the DAB module and disconnect the DAB connector.
4. Disconnect the connectors of the PAB, SAB, CAB, BPT, FIS and SIS.
5. Disconnect the SRSCM connector.
2. CHECK BUPT RESISTANCE
CAUTION: Never attempt to measure the circuit resistance of the airbag module(squib) even if you are using the specified tester.
1. Connect the Dummy and the Dummy Adapter on BUPT harness connector.
- Refer to "SPECIAL SERVICE TOOL" section in this SERVICE MANUAL for the SST No. of Dummy and Dummy Adapter.
2. Measure resistance between the terminal 16 (13) and 15 (14) of SRSCM harness connector.
BUPT resistance : 1.5 - 5.7 ohms
3. Is the measured resistance within specification?
YES - Replace the Buckle Pretensioner(BUPT) module.
NO - Check open circuit.
3. CHECK OPEN CIRCUIT
1. Measure resistance between the terminal 1 of BUPT harness connector and the terminal 16 (13) of SRSCM harness connector.
2. Measure resistance between the terminal 2 of BUPT harness connector and the terminal 15 (14) of SRSCM harness connector.
specification (resistance) : below 1 ohm
3. Is the measured resistance within specification
YES - Check short circuit.
NO - Repair or replace the wiring harness between the BUPT and the SRSCM.
4. CHECK SHORT CIRCUIT
1. Measure resistance between the terminal 1 and 2 of BUPT harness connector.
specification (resistance) : infinite
2. Is the measured resistance within specification?
YES - Go to next step.
NO - Repair or replace the wiring harness between the BUPT and the SRSCM.
5. CLEAR THE DTC AND CHECK THE VEHICLE AGAIN
1. Install the DAB module and connect the DAB connector.
2. Connect the connector of the PAB, SAB, CAB, BPT, BUPT, FIS and SIS.
3. Connect the SRSCM connector.
4. Connect the battery negative cable to the battery.
5. Connect a Hi-Scan(Pro) to the data link connector.
6. Turn the ignition switch to ON.
7. Clear the DTC stored in the SRSCM memory with the Hi-Scan(Pro)
8. Turn the ignition switch to LOCK and wait for at least 30 seconds.
9. Turn the ignition switch to ON and wait for at least 30 seconds.
10. Check the vehicle again with the Hi-Scan (Pro).
Does the above DTC(s) go off?
YES - Problem s intermittent or was repaired and SRSCM memory was not cleared.
NO - Replace the SRSCM with a new one and then check the vehicle again. At this time, if the vehicle normally operates with a new one, the fault may be the SRSCM. Replace the SRSCM.