Repair Procedures

Removal

Smart Key Unit
1. Disconnect the negative (-) battery terminal.
2. Remove the crash pad lower panel (A). Avoid damaging retaining clip.




3. After loosening the smart key unit IPM mounting nuts and disconnect the connector, remove the smart key unit (A).





RF Receiver
1. Disconnect the negative (-) battery terminal.
2. After loosening the mounting screws and bolts, then remove the glove box (A).




3. Remove the glove box housing connector (A).




4. Remove the DIS (Driver Information System) head unit.
5. Remove the USB interface unit.
6. Remove the Front/Rear Parking assist system unit.
7. Remove the Adaptive Front lighting system unit.
8. After loosening the mounting nuts and connector (A), then remove the RF receiver (B).





Interior 1 Antenna
1. Disconnect the negative (-) battery terminal.
2. Remove the DIS (Driver Information System).
3. Remove the interior 1 antenna (A) after removing the nuts and connector.





Interior 2 Antenna
1. Disconnect the negative (-) battery terminal.
2. Remove the floor console assembly (A) after removing the bolts and nuts.




3. Remove the interior 2 antenna (A) after removing the nuts and connector.





Interior 3 Antenna
1. Disconnect the negative (-) battery terminal.
2. Remove the rear seat assembly.
3. Remove the package tray trim (A) after removing the screws.




4. Remove two interior 3 antennas (A) after removing the bolts and connector.





Trunk Antenna
1. Disconnect the negative (-) battery terminal.
2. Remove the rear seat assembly
3. Remove the trunk carpet (A).




4. Remove the trunk antenna (A) after removing the bolts and connector.





Exterior Bumper Antenna
1. Disconnect the negative (-) battery terminal.
2. Remove the rear bumper.
3. After loosening the antenna connector on the rear bumper and screws(2EA), remove the exterior bumper antenna (A).





Buzzer
1. Disconnect the negative (-) battery terminal.
2. Remove the Engine Control Module (ECM). (Refer to Fuel group - Engine Control Module (ECM))
3. Remove the buzzer (A) after disconnecting the connector and removing nut.





Door Outside Handle
1. Disconnect the negative (-) battery terminal.
2. Remove the door trim.
3. After loosening the mounting bolt, then remove the key cylinder (A).




4. Remove the outside handle (A) by sliding it rearward.




5. Disconnect the outside handle connector (A).





Trunk Lid Switch
1. Disconnect the negative (-) battery terminal.
2. Remove the Trunk lid panel (A).




3. Remove the trunk lid switch from the license lamp and the trunk lid switch assembly (A) after loosening the bolts.




4. Remove the trunk lid switch after disconnecting the connector (A).






Installation

Smart Key Unit (IPM)
1. Install the smart key unit and connector.
2. Install the crash pad lower panel.
3. Connect the negative (-) battery terminal and check the smart key system.

RF Receiver
1. Install the connector and RF receiver.
2. Install the AFLS unit.
3. Install the Front/Rear Parking assist system unit.
4. Install the USB interface unit.
5. Install the DIS head unit.
6. Install the glove box housing connector and glove box.
7. Connect the negative (-) battery terminal and check the smart key system.

Interior 1 Antenna
1. Install the interior 1 antenna and connector.
2. Install the DIS head unit.
3. Install the center fascia panel.
4. Connect the negative (-) battery terminal and check the smart key system.

Interior 2 Antenna
1. Install the interior 2 antenna and connector.
2. Install the floor console assembly.
3. Connect the negative (-) battery terminal and check the smart key system.

Interior 3 Antenna
1. Install the interior 3 antenna and connector.
2. Install the package tray trim and rear seat assembly.
3. Connect the negative (-) battery terminal and check the smart key system.

Trunk Antenna
1. Install the trunk antenna and connector.
2. Install the trunk carpet.
3. Connect the negative (-) battery terminal and check the smart key system.

Exterior Bumper Antenna
1. Install the exterior bumper antenna and connector.
2. Install the rear bumper.
3. Connect the negative (-) battery terminal and check the smart key system.

Buzzer
1. Install the buzzer on the front shock absorber.
2. Install the fender.
3. Connect the negative (-) battery terminal and check the smart key system.

Door Outside Handle
1. Install the outside handle.
2. Install the door trim and cover.
3. Install the negative (-) battery terminal and check the smart key system.

Trunk Lid Switch
1. Install the trunk lid switch and trunk lid panel.
2. Install the negative (-) battery terminal and check the smart key system.

Inspection

Smart Key Unit

- Refer to the Smart key System - Inspection / self diagnosis with GDS

Smart Key Switch
- Refer to the Smart key System - Inspection / self diagnosis with GDS

Antenna
- Refer to the Smart key System - Inspection / self diagnosis with GDS

Trunk Lid Switch
1. Check for continuity between the terminals of switch connector (A).




2. If continuity is not specified, inspect the switch






Smart Key

Smart Key Code Saving
1. Connect the DLC cable of GDS to the data link connector (16 pins) in driver side crash pad lower panel, turn the power on GDS.




2. Select the vehicle model and then do "Smart key code saving".




3. After selecting "Smart key teaching" menu, push "Enter" key, then the screen will be shown as below.




4. After inserting the teaching key, push "ENTER" key.
5. Input the "Pin code" for first key teaching.








6. Confirm the message "First key teaching completed".








7. Input the "Pin code" for second key teaching.








8. Confirm the message "Second key teaching completed".