Exterior Moulding / Trim: Service and Repair

Replacement

Roof Garnish Replacement
[General Type]

CAUTION:
- When prying with a flat-tip screwdriver, wrap it with protective tape, and apply protective tape around the related parts, to prevent damage
- Put on gloves to protect your hands.
- Take care not to scratch the body surface.

1. Using a screwdriver or remover, remove the roof garnish (A).

NOTE:
- Replace any damaged roof garnish.




2. Installation is the reverse of removal.

NOTE:
- Replace any damaged clips.

Roof Garnish Replacement
[Panoramaroof Type]

CAUTION:
- When prying with a flat-tip screwdriver, wrap it with protective tape, and apply protective tape around the related parts, to prevent damage
- Put on gloves to protect your hands.
- Take care not to scratch the body surface.

1. Open the movable glass fully.
2. Using a screwdriver or remover, remove the roof garnish (A).

NOTE:
- Replace any damaged roof garnish.




3. Installation is the reverse of removal.

NOTE:
- Replace any damaged clips.

Front Wheel Guard Replacement

CAUTION:
- When prying with a flat-tip screwdriver, wrap it with protective tape, and apply protective tape around the related parts, to prevent damage
- Put on gloves to protect your hands.
- Take care not to scratch the body surface.

1. Remove the front tire.
2. After loosening the mounting clips and screws, then remove the front wheel guard (A).
[LH]




[RH]




3. Installation is the reverse of removal.

NOTE:
- Replace any damaged clips.

Rear Wheel Guard Replacement

CAUTION:
- When prying with a flat-tip screwdriver, wrap it with protective tape, and apply protective tape around the related parts, to prevent damage
- Put on gloves to protect your hands.
- Take care not to scratch the body surface.

1. Remove the rear tire.
2. After loosening the mounting clips and screws, then remove the rear wheel guard (A).
[LH]




[RH]




3. Installation is the reverse of removal.

NOTE:
- Replace any damaged clips.

Hood Garnish Replacement

CAUTION:
- When prying with a flat-tip screwdriver, wrap it with protective tape, and apply protective tape around the related parts, to prevent damage
- Put on gloves to protect your hands.
- Take care not to scratch the body surface.

1. Remove the hood insulator pad.

2. After loosening the mounting nuts, then remove the hood garnish (A).

Tightening torque :
3.9 - 4.4 N.m (0.4 - 0.45 kgf.m, 2.9 - 3.3 lb-ft)




3. Installation is the reverse of removal.

NOTE:
- Replace any damaged clips.

A Pillar Garnish Replacement

CAUTION:
- When prying with a flat-tip screwdriver, wrap it with protective tape, and apply protective tape around the related parts, to prevent damage.
- Put on gloves to protect your hands.
- Take care not to scratch the body surface.

1. To remove the A pillar garnish (A), loosen the mounting screw after removing the cap (B).

Tightening torque :
0.5 - 1.0N.m (0.05 - 0.1kgf.m, 0.4 - 0.7 lb-ft)




2. Installation is the reverse of removal.

NOTE:
- Replace any damaged clips.

Quarter Fixed Glass & Molding Replacement

CAUTION:
- When prying with a flat-tip screwdriver, wrap it with protective tape, and apply protective tape around the related parts, to prevent damage.
- Put on gloves to protect your hands.
- Take care not to scratch the body surface.

1. Remove the following items.
A. Rear seat

B. Front seat belt lower anchor

C. Front door scuff trim

D. Center pillar lower trim

E. Center pillar upper trim

F. Luggage side trim

G. Rear pillar trim

2. After loosening the mounting nuts, then remove the quarter fixed glass & molding (A).

Tightening torque :
3.9 - 4.4 N.m (0.4 - 0.45 kgf.m, 2.9 - 3.3 lb-ft)




3. Installation is the reverse of removal.

NOTE:
- Replace any damaged clips.

Rear Spoiler Replacement

CAUTION:
- When prying with a flat-tip screwdriver, wrap it with protective tape, and apply protective tape around the related parts, to prevent damage.
- Put on gloves to protect your hands.
- Take care not to scratch the body surface.

1. Remove the following items.
A. Tail gate frame upper trim & Tail gate center trim

B. Tail gate trim

C. Tail gate frame side trim

2. Disconnect the washer nozzle (B) and high mounted stop lamp connector (A).




3. Loosen the rear spoiler mounting nuts.

Tightening torque :
5.9 - 6.4 N.m (0.6 - 0.65 kgf.m, 4.3 - 4.7 lb-ft)




4. Remove the rear spoiler (A).




5. Installation is the reverse of removal.

NOTE:
- Make sure the connector are connected in properly.
- Replace any damaged clips.