Operation CHARM: Car repair manuals for everyone.
Home >> Hyundai >> 2013 >> Genesis Coupe L4-2.0L Turbo >> Repair and Diagnosis >> Body and Frame >> Interior Moulding / Trim >> Dashboard / Instrument Panel >> Service and Repair >> Repair Procedures

Repair Procedures





Replacement

Cluster Replacement

NOTE:
- When prying with a flat-tip screwdriver, wrap it with protective tape, and apply protective tape around the related parts, to prevent damage.
- Take care not to scratch the body surface
- Put on gloves to protect your hands.

1. Using a screwdriver or remover, remove the cluster fascia lower panel (A).




2. After loosening the mounting screws, then remove the cluster assembly (A).




3. Disconnect the connector (A).




4. Installation is the reverse the removal.

NOTE:
- Make sure the connector is connected properly.
- Replace any damaged clips.

Center Fascia Panel Replacement

NOTE:
- When prying with a flat-tip screwdriver, wrap it with protective tape, and apply protective tape around the related parts, to prevent damage.
- Take care not to scratch the body surface
- Put on gloves to protect your hands.

1. Using a screwdriver or remover, remove the center fascia upper panel (A).




2. Disconnect the connector (A).




3. Using a screwdriver or remover, remove the console upper cover (A).




4. Using a screwdriver or remover, remove the center fascia lower panel (A).




5. Disconnect the connectors (A).
[Upper]




[Lower]




6. Installation is the reverse of removal.

NOTE:
- Make sure the connector is connected properly.
- Replace any damaged clips.

Crash Pad Lower Panel Replacement

NOTE:
- When prying with a flat-tip screwdriver, wrap it with protective tape, and apply protective tape around the related parts, to prevent damage.
- Take care not to scratch the body surface
- Put on gloves to protect your hands.

1. Using a screwdriver or remover, remove the crash pad side cover (A).




2. After loosening the mounting screws, then remove the crash pad lower panel (A).




3. Disconnect the crash pad lower switch connectors (A).




4. Disconnect the start/stop button connector (A).




5. Disconnect the diagnosis connector (A).




6. Installation is the reverse of removal.

NOTE:
- Make sure the connector is connected properly.
- Replace any damaged clips.

Audio Unit Assembly Replacement

NOTE:
- When prying with a flat-tip screwdriver, wrap it with protective tape, and apply protective tape around the related parts, to prevent damage.
- Take care not to scratch the body surface
- Put on gloves to protect your hands.

1. Using a screwdriver or remover, remove the center fascia upper panel (A).




2. Disconnect the connector (A).




3. Using a screwdriver or remover, remove the console upper cover (A).




4. Using a screwdriver or remover, remove the center fascia lower panel (A).




5. Disconnect the connectors (A).
[Upper]




[Lower]




6. After loosening the mounting screws, then remove the audio unit assembly (A).




7. Disconnect the audio unit connectors (A).




8. Installation is the reverse of removal.

NOTE:
- Make sure the connector is connected properly.
- Replace any damaged clips.

Monitor Assembly Replacement

NOTE:
- When prying with a flat-tip screwdriver, wrap it with protective tape, and apply protective tape around the related parts, to prevent damage.
- Take care not to scratch the body surface
- Put on gloves to protect your hands.

1. Using a screwdriver or remover, remove the center fascia upper panel (A).




2. Disconnect the connector (A).




3. After loosening the mounting screws, then remove the monitor assembly (A).




4. Disconnect the monitor connector (A).




5. Installation is the reverse of removal.

NOTE:
- Make sure the connector is connected properly.
- Replace any damaged clips.

Glove Box Housing Replacement

NOTE:
- When prying with a flat-tip screwdriver, wrap it with protective tape, and apply protective tape around the related parts, to prevent damage.
- Take care not to scratch the body surface
- Put on gloves to protect your hands.

1. Using a screwdriver or remover, remove the crash pad side cover (A).




2. Disconnect the stopper (B) from the glove box (A).




3. Disconnect the air damper (A) from the glove box (B).




4. Disconnect the pin (A) and then remove the glove box (B).




5. After loosening the mounting screws and bolts, then remove the glove box housing (A).




6. Installation is the reverse of removal.

NOTE:
- Replace any damaged clips.

Main Crash Pad Replacement

NOTE:
- When prying with a flat-tip screwdriver, wrap it with protective tape, and apply protective tape around the related parts, to prevent damage.
- Take care not to scratch the body surface
- Put on gloves to protect your hands.

1. Remove the front seat assembly.

2. Remove the front pillar trim.

3. Remove the floor console assembly

4. Remove the front door scuff trim.

5. Remove the cowl side trim.

6. Remove the crash pad side cover [LH, RH].
7. Remove the cluster fascia lower panel.
8. Remove the cluster assembly.
9. Remove the crash pad lower panel.
10. Remove the center fascia upper panel.
11. Remove the center fascia lower panel.
12. Remove the monitor assembly.
13. Remove the audio unit assembly.
14. Remove the glove box.
15. Remove the glove box housing.
16. Remove the steering column shroud.
17. Disconnect the steering column connectors.

18. Down the steering column after loosening the mounting bolts.

19. Disconnect the passenger`s airbag connector (A).
20. Loosen the mounting bolts.




21. Disconnect the center speaker connector (A).




22. Disconnect the trip switch connector (A).




23. Using a screwdriver or remover, remove the photo sensor (A).
24. Disconnect the photo sensor connector (B).




25. After loosening the mounting bolts and nuts, then remove the main crash pad assembly (B).




26. Installation is the reverse of removal.

NOTE:
- Make sure the crash pad fits onto the guide pins correctly.
- Before tightening the bolts, make sure the crash pad wire harnesses are not pinched.
- Make sure the connectors are plugged in properly, and the antenna lead is connected properly.
- Enter the anti- theft code for the radio, then enter the customer`s radio station presets.

Cowl Cross Bar Replacement

NOTE:
- When prying with a flat-tip screwdriver, wrap it with protective tape, and apply protective tape around the related parts, to prevent damage.
- Take care not to scratch the body surface
- Put on gloves to protect your hands.

1. Remove the front seat assembly.

2. Remove the front pillar trim.

3. Remove the floor console assembly

4. Remove the front door scuff trim.

5. Remove the cowl side trim.

6. Remove the cowl top cover.

7. Remove the main crash pad.
8. Disconnect the blower unit connectors.

9. Disconnect the multi box connectors (A).
[Driver's]




[Passenger's]




10. Disconnect the passenger compartment junction box connectors (A).




11. Disconnect the airbag control module (SRSCM) connectors (A).
12. Remove the airbag control module wiring mounting clips (B).




13. After loosening the mounting bolts and nuts, then remove the cowl cross bar assembly (A).




14. Installation is the reverse of removal.

NOTE:
- Make sure the cowl cross bar fits onto the guide pins correctly.
- Before tightening the bolts, make sure the crash pad wire harnesses are not pinched.
- Make sure the connectors are plugged in properly, and the antenna lead is connected properly.

pro multis · About Operation CHARM