Front Seat
Replacement
Front Seat Assembly Replacement
1. Remove the front foot cover.
2. After loosening the front seat assembly mounting bolts, remove the front seat assembly (A).
Tightening torque :
49.0 - 63.7N.m (5.0 - 6.5kgf.m, 36.2 - 47.0lb-ft)
3. Disconnect the airbag connector (A), seat warmer connector (B), seat buckle connector (C).
[Driver's]
[Passenger's]
4. Installation is the reverse of removal.
CAUTION:
Seat Mounting Bolt Installation Procedure
- Set the into the most rearward position. Check then each slide is locked, and then Tighten the front mounting bolt temporarily.
- Set the seat into most forward position. Check that each slide is locked, and then Tighten the rear mounting bolt completely.
- Set the seat into the most rearward position. Check the front mounting bolt completely.
- Check that the seat operates back and forth smoothy and the locking portion locks properly.
Recliner Cover Replacement
NOTE:
- Use a plastic panel removal tool to remove interior trim pieces to protect from marring the surface.
- Take care not to bend or scratch the trim and panels.
- Put on gloves to protect your hands.
1. Remove the recliner lever (A) and height lever (B).
2. After loosening the mounting screws, then remove the recliner cover (A).
3. Disconnect the connector.
4. Installation is the reverse of removal.
NOTE:
- Make sure the connector is plugged in properly.
- Replace any damaged clips.
Front Seat Back Cover Replacement
NOTE:
- Use a plastic panel removal tool to remove interior trim pieces to protect from marring the surface.
- Take care not to bend or scratch the trim and panels.
- Put on gloves to protect your hands.
1. Remove the front seat assembly.
2. Remove the recliner cover.
3. Remove the front seat headrest.
4. Remove the lumber support level.
5. After disconnecting the clips (C) and (B), remove the front seat back board (A).
6. Push the protector (A) by the seat back frame.
7. Disconnect the airbag connectors (A).
8. Pull out the headrest guides (A) while pinching the end of the guides, and remove them.
9. Remove the front seat back cover from the frame.
10. After removing the velcro tape (A) and hog-ring clip (B) on the front of seat back and remove the front seat back cover (C).
11. Installation is the reverse of removal.
NOTE:
- To prevent wrinkles, make sure the material is stretched evenly over the cover (B) before securing the hog-ring clips (A).
- Replace the hog ring clips with new ones using special tool [C (09880-4F000)].
Front Seat Cushion Cover Replacement
NOTE:
- Use a plastic panel removal tool to remove interior trim pieces to protect from marring the surface.
- Take care not to bend or scratch the trim and panels.
- Put on gloves to protect your hands.
1. Remove the front seat assembly.
2. Remove the recliner cover.
3. Disconnect the connector (A).
4. Push the protector, and then front seat cushion cover (A) from the frame.
5. After removing the velcro tape (B) on the front of seat cushion and remove the front seat cushion cover (A).
6. Installation is the reverse of removal.
NOTE:
- Make sure the connector is plugged in properly.
- Replace any damaged clips.
Front Seat Frame Replacement
NOTE:
- Use a plastic panel removal tool to remove interior trim pieces to protect from marring the surface.
- Take care not to bend or scratch the trim and panels.
- Put on gloves to protect your hands.
1. Remove the front seat assembly.
2. Remove the recliner cover.
3. Remove the front seat back cover.
4. Remove the front seat cushion cover.
5. After loosening the mounting bolts, then disconnect the seat back frame (A) and seat cushion frame (B).
Tightening torque :
49.0 - 63.7N.m (5.0 - 6.5kgf.m, 36.2 - 47.0lb-ft)
6. Installation is the reverse of removal.
NOTE:
- Remove the side air bag for replacing side air bag installation seat.
- Before service, be fully aware of precautions and service procedure relevant to air bag.
Front Seat Back Heater Replacement
NOTE:
- Use a plastic panel removal tool to remove interior trim pieces to protect from marring the surface.
- Take care not to bend or scratch the trim and panels.
- Put on gloves to protect your hands.
1. Remove the front seat assembly.
2. Remove the front seat back cover.
3. Remove the front seat back heater (A).
4. Installation is the reverse of removal.
Front Seat Cushion Heater Replacement
NOTE:
- Use a plastic panel removal tool to remove interior trim pieces to protect from marring the surface.
- Take care not to bend or scratch the trim and panels.
- Put on gloves to protect your hands.
1. Remove the front seat assembly.
2. Remove the front seat cushion cover.
3. Remove the front seat cushion heater (A).
4. Installation is the reverse of removal.