Control Panel Mode
Control Panel Mode
APPLICATION ITEMS
HOW TO PERFORM CONTROL PANEL MODE
1. Start the engine.
2. Push "OPEN/CLOSE" switch and then open the display.
3. Push "SETTING" switch.
- For further procedures, refer to the following pages which describe each application item of the control panel mode.
"DISPLAY AUTO OPEN" MODE
1. Start the engine.
2. Push "OPEN/CLOSE" switch and then open the display.
3. Push "SETTING" switch.
4. Select "System Setting".
5. Select "Display Auto Open".
6. Select "Auto" or "Manual" icon.
- To manually open the display, select "Manual".
- To automatically open the display, select "Auto".
7. Push "MAP" switch, then the display will go back to the current location map.
"GPS INFORMATION" MODE
1. Start the engine.
2. Push "OPEN/CLOSE" switch and then open the display.
3. Push "SETTING" switch.
4. Select "System Setting".
5. Select "GPS information".
6. Then GPS information will be displayed.
"QUICK STOP CUSTOMER SETTING" MODE
1. Start the engine.
2. Push "OPEN/CLOSE" switch and then open the display.
3. Push "SETTING" switch.
4. Select "System Setting".
5. Select "Quick Stop Customer Setting".
6. Select an item from the list.
"ROUTE PRIORITIES" MODE
1. Start the engine.
2. Push "OPEN/CLOSE" switch and then open the display.
3. Push "SETTING" switch.
4. Select "System Setting".
5. Select "Route Priorities".
6. Select an item from the list.
"TRACKING" MODE
1. Start the engine.
2. Push "OPEN/CLOSE" switch and then open the display.
3. Push "SETTING" switch.
4. Select "System Setting".
5. Select "Tracking".
6. Select "On" or "Off" icon.
- To leave no trail on the map, select "Off".
- To leave a trail in the map, select "On".
7. Push "MAP" switch, then the display will go back to the current location map.
NOTE: When a trail display is turned OFF, trail data is erased from the memory.
"DISPLAY SETTING" MODE
Display Color Setting
1. Start the engine.
2. Push "OPEN/CLOSE" switch and then open the display.
3. Push "SETTING" switch.
4. Select "System Setting".
5. Select "Color". Display color will change to Day mode/Night mode.
6. Select "MAP" switch, then the display will go back to the current location map.
NOTE:
- Display color can be changed independently when lighting switch is turned on and off.
- Initial setting of the color is as follows: When lighting switch is turned off: Day mode When lighting switch is turned on: Night mode
Brightness Setting
1. Start the engine.
2. Push "OPEN/CLOSE" switch and then open the display.
3. Push "SETTING" switch.
4. Select "System Setting".
5. Select "Bright" or "Dark" to adjust the brightness of display.
6. Select "MAP" switch, then the display will go back to the current location map.
NOTE: Display brightness can be adjusted independently when lighting switch is turned on and off.
"HEADING" MODE
1. Start the engine.
2. Push "OPEN/CLOSE" switch and then open the display.
3. Push "SETTING" switch.
4. Select "System Setting".
5. Select "Heading".
6. Select "Heading up" or "North up" icon.
- To display North up, select "North up".
- To display the car heading up, select "Heading up".
7. Push "MAP" switch, then the display will go back to the current location map.
"NEARBY DISPLAY ICONS" MODE
1. Start the engine.
2. Push "OPEN/CLOSE" switch and then open the display.
3. Push "SETTING" switch.
4. Select "System Setting".
5. Select "Nearby Display Icons".
6. Select and touch an item on the list.
7. Push "MAP" switch, then the display will go back to the current location map.
"ADJUST CURRENT LOCATION" MODE
1. Start the engine.
2. Push "OPEN/CLOSE" switch and then open the display.
3. Push "SETTING" switch.
4. Select "System Setting".
5. Select "Adjust Current Location".
6. Select "<-" or "->" to calibrate the heading direction. (Arrow marks will rotate corresponding to the calibration key.)
7. Select "Set". Then the vehicle mark will be matched to the arrow mark.
8. Display will show "Heading direction has been calibrated" and then go back to the current location map.
"BEEP ON/OFF" MODE
1. Start the engine.
2. Push "OPEN/CLOSE" switch and then open display.
3. Push "SETTING" switch.
4. Select "System Setting".
5. Touch "Beep On/Off".
6. Select "On" or "Off" icon.
- If you want the beep sound, select "On".
- If you do not want the beep sound, select "Off".
7. Push "PREVIOUS" switch, then the display will go back to the current location map.
"CLEAR MEMORY" MODE
1. Start the engine.
2. Push "OPEN/CLOSE" switch and then open the display.
3. Push "SETTING" switch.
4. Select System Setting .
5. Select Clear Memory .
6. To delete all the stored places in "Address Book", "Avoid Area" and "Previous Dest", select "Yes".