C1963

B1342-ECU is defective

Possible Source(s):
^ DSC/TCS module internal failure.
^ Processor failure.
^ DSC/TCS module failure.

Action(s) to take:
^ GO to [Pinpoint Test A]. Test A-ABS Control Module Is Defective

C1095-DSC hydraulic pump motor circuit failure

Possible Source(s):
^ Harness fault.
^ Connector loose or corroded.
^ Connector pins(s) bent or tracking between connections.
^ Ground failure.

Action(s) to take:
^ GO to [Pinpoint Test B]. Test B-C1095-ABS Hydraulic Pump Motor Circuit Failure

C1145, C1155, C1165, C1175-RF, LF, RR, LR wheel speed circuit failure

Possible Source(s):
^ Harness fault.
^ Connector loose or corroded.
^ Connector pin(s) bent or tracking between connections.

Action(s) to take:
^ GO to [Pinpoint Test C]. Pinpoint Tests

C1233, C1234, C1235, C1236-LF, RF, RR, LR wheel speed input signal missing

Possible Source(s):
^ Sensor gap incorrect.
^ Foreign matter on sensor face.
^ Missing tooth on wheel.
^ Faulty Sensor.

Action(s) to take:
^ GO to [Pinpoint Test D]. Pinpoint Tests

B1485-Stop lamp switch input circuit short to positive voltage

Possible Source(s):
^ Harness fault.
^ Connector pin(s) bent or tracking between connections.

Action(s) to take:
^ GO to [Pinpoint Test E]. Test E-B1485-Stop Lamp Sw. Input Circuit Short to Pos. Voltage

B1676-Battery voltage out of range

Possible Source(s):
^ Battery voltage to DSC module out of range.
^ Harness fault.
^ Connector pin(s) bent or tracking between connections.

Action(s) to take:
^ GO to [Pinpoint Test F]. Test F-B1676 - Battery Voltage Out of Range

B2477-Module configuration failure

Possible Source(s):
^ Module not configured.
^ Module configuration data incorrect.

Action(s) to take:

C1279-Yaw rate sensor circuit failure

Possible Source(s):
^ Yaw rate sensor open/short circuit.
^ Damaged harness.
^ Connector pins bent or corroded.
^ Damaged DSC module.

Action(s) to take:
^ GO to [Pinpoint Test G].

C1280-Yaw rate sensor signal fault

Possible Source(s):
^ Yaw rate sensor signal open/short circuit.
^ Damaged harness.
^ Connector pins bent or corroded.
^ Damaged DSC module.

Action(s) to take:
^ GO to [Pinpoint Test H].

C1281-Lateral accelerometer circuit failure

Possible Source(s):
^ Lateral accelerometer open/short circuit.
^ Damaged harness.
^ Connector pins bent or corroded.
^ Damaged DSC module.

Action(s) to take:
^ GO to [Pinpoint Test I].

C1282-Lateral accelerometer signal failure

Possible Source(s):
^ Lateral Accelerometer signal open/short circuit.
^ Damaged harness.
^ Connector pins bent or corroded.
^ Damaged DSC module.

Action(s) to take:
^ GO to [Pinpoint Test J].

C1285-Booster solenoid output circuit failure

Possible Source(s):
^ Booster solenoid output open/short circuit.
^ Connector pins bent or corroded.
^ Damaged harness.
^ Damaged DSC module.

Action(s) to take:
^ GO to [Pinpoint Test K].

C1286-Booster mechanical failure

Possible Source(s):
^ Damaged vacuum pipe.
^ Damaged brake booster.

Action(s) to take:
^ GO to [Pinpoint Test L].

C1287-Booster pedal force switch circuit failure

Possible Source(s):
^ Booster pedal force switch open/short circuit.
^ Connector pins bent or corroded.
^ Damaged harness.
^ Damaged DSC module.

Action(s) to take:
^ GO to [Pinpoint Test M].

C1288-Pressure transducer main/primary input circuit failure

Possible Source(s):
^ Pressure transducer main/primary input open/short circuit.
^ Connector pins bent or corroded.
^ Damaged harness.
^ Damaged DSC module.

Action(s) to take:
^ GO to [Pinpoint Test N].

C1289-Pressure transducer redundant/secondary input circuit failure

Possible Source(s):
^ Pressure transducer redundant/secondary input open/short circuit.
^ Connector pins bent or corroded.
^ Damaged harness.
^ Damaged DSC module.

Action(s) to take:
^ GO to [Pinpoint Test O].

C1277-Steering wheel angle 1 and 2 circuit failure

Possible Source(s):
^ Steering wheel angle 1 and 2 open/short circuit.
^ Connector pins bent or corroded.
^ Damaged harness.
^ Damaged DSC module.

Action(s) to take:
^ GO to [Pinpoint Test P].

C1278-Steering wheel angle 1 and 2 signal faulted

Possible Source(s):
^ Steering wheel angle 1 and 2 signal open/short circuit.
^ Connector pins bent or corroded.
^ Damaged harness.
^ Damaged DSC module.

Action(s) to take:
^ GO to [Pinpoint Test Q].

C1730-Reference voltage out of range (+5)

Possible Source(s):
^ DSC sensor open/short circuit.
^ Connector pins bent or corroded.
^ Damaged harness.
^ Damaged DSC module.

Action(s) to take:
^ GO to [Pinpoint Test R].

C1963-Stability control inhibit warning

Possible Source(s):
^ Yaw control inhibited due to persisting initiating conditions.

Action(s) to take:
^ Check the configuration of the DSC control module and the instrument cluster.

C1969-TC/YC switch lamp circuit fault

Possible Source(s):
^ Module configuration between DSC control module and the instrument cluster.

Action(s) to take:
^ Check the configuration of the DSC control module and the instrument cluster.