Electronic Engine Controls
Electronic Engine Controls
Powertrain Control Module (PCM)
The electronic engine control system consists of a powertrain control module (PCM) and a number of sensing and actuating devices. The sensors supply the PCM with input signals which relate to the engine operating conditions and driver requirements. The sensor information is evaluated by the PCM using the results to activate the appropriate response from the actuating devices. The system provides the necessary engine control accuracy and adaptability to:
- Minimize exhaust emissions and fuel consumption.
- Provide optimum driver control under all conditions.
- Minimize evaporative emissions.
- Provide system diagnostics.
In addition to these functions the PCM also interfaces with other vehicle systems through the controller area network (CAN).
Camshaft Position (CMP) Sensor
The camshaft position (CMP) sensors monitor the position of both camshafts to allow the PCM to control the phase of the inlet camshafts relative to the position of the crankshaft.
Variable Camshaft Timing Oil Control Solenoid
The variable camshaft timing oil control solenoid is a hydraulic actuator, which advances and retards the inlet camshaft timing, thereby altering the camshaft to crankshaft phasing for optimum engine performance.
Intake Manifold Tuning (IMT) Valve
There are two intake manifold tuning (IMT) valves, an upper and a lower, sometimes referred to as number one and two respectively. They are a two position (open and close) device used to create a variable air intake system. The IMT valve positions are switched by signals from the PCM to optimize torque across the engine's speed and load range. The IMT valves work in conjunction with the throttle body. The upper IMT valve opens between 3,000 and 6,000 rpm while the lower IMT valve opens between 5,000 and 6,000 rpm.
Knock Sensor (KS)
The knock sensor (KS) detects combustion knock within the engine cylinders and sends a signal to the PCM. The PCM uses this information to gradually adjust the ignition timing until the combustion knock is eliminated.
Mass Air flow (MAF) Sensor
The mass air flow (MAF) sensor informs the PCM of the rate of air flow entering the engine by producing a voltage which is proportional to the rate of air flow into the engine. The voltage produced by the MAF sensor increases as the rate of air flow increases. The MAF sensor also takes into account the density of the air entering the air intake system so that it is possible to maintain the required air to fuel ratio, and to compensate for variations in atmospheric pressure.
Integral to the MAF sensor is the intake air temperature sensor (IAT) which measures the temperature of the air entering the air intake system. The PCM uses this information to compensate for higher than normal air intake temperatures.
Throttle Position (TP) Sensor
The PCM monitors the angle of the throttle plate within the throttle housing through the throttle position (TP) sensor. The TP sends a voltage to the PCM which is proportional to the angle of the throttle plate. The voltage from the TP increases with the angle of the throttle plate. There are two sensor tracks within the TP sensor.
Crankshaft Position (CKP) Sensor
The crankshaft position (CKP) sensor is an inductive pulse generator, which scans protrusions on a pulse ring fitted to the front of the crankshaft to inform the PCM of the crankshaft's position and speed. The CKP sensor produces an alternating voltage which is increases with engine speed.
Engine Coolant Temperature (ECT) Sensor
The engine coolant temperature (ECT) sensor is a thermistor type sensor that provides an input signal to the PCM which is proportional to the engine coolant temperature. The ECT sensor is a negative temperature coefficient (NTC) sensor and its resistance decreases with a proportional increase in engine coolant temperature.
Oil Temperature Sensor
The oil temperature sensor is a thermistor type sensor that provides an input signal to the PCM which is proportional to the engine oil temperature.
Oil Pressure Switch
The oil pressure switch is connected to the instrument cluster and is not directly part of the electronic engine control system.
Heated Oxygen Sensor (HO2S)
The heated oxygen sensor (HO2S) is a linear characteristic type sensor, fitted forward of the exhaust system's catalytic converter. The PCM uses this as it's primary sensor to measure the oxygen content of the exhaust gasses within the exhaust system to provide closed-loop fuelling control.
Catalyst Monitor Sensor
The catalyst monitor sensor is a non-linear characteristic type sensor fitted to the exhaust system's catalytic converter. The PCM uses this as it's secondary sensor to measure the oxygen content of the exhaust gasses within the exhaust after they have passed through the catalytic converter. As well as providing additional closed-loop fuelling control the PCM uses this information to determine the efficiency of the catalytic converter.