P0706

D: P0706. TRANSMISSION RANGE SENSOR MALFUNCTION
CHECK TRANSMISSION RANGE SENSOR CONTINUITY IN PARK.
1. Disconnect TO sensor electrical connector JB156.
2. Select PARK.
3. Check for continuity between pins 08 and 09 of the sensor.
^ Is the circuit continuous?
-> Yes
-> No
Carry out the adjustment procedure for the transmission range sensor. Recheck the circuit. If still open circuit, INSTALL a new transmission range sensor. CLEAR the DTC. TEST the system for normal operation.

CHECK TRANSMISSION RANGE SENSOR CONTINUITY IN REVERSE.
1. Select REVERSE.
2. Check for continuity between pins 08 and 07 of the sensor.
^ Is the circuit continuous?
-> Yes
-> No
Carry out the adjustment procedure for the transmission range sensor. Recheck the circuit. If still open circuit, INSTALL a new transmission range sensor. CLEAR the DTC. TEST the system for normal operation.

CHECK TRANSMISSION RANGE SENSOR CONTINUITY IN NEUTRAL.
1. Select NEUTRAL.
2. Check for continuity between pins 08 and 02 of the sensor.
^ Is the circuit continuous?
-> Yes
-> No
Carry out the adjustment procedure for the transmission range sensor. Recheck the circuit. If still open circuit, INSTALL a new transmission range sensor. CLEAR the DTC. TEST the system for normal operation.

CHECK TRANSMISSION RANGE SENSOR CONTINUITY IN D.
1. Select D.
2. Check for continuity between pins 08 and 01 of the sensor.
^ Is the circuit continuous?
-> Yes
-> No
Carry out the adjustment procedure for the transmission range sensor. Recheck the circuit. If still open circuit, INSTALL a new transmission range sensor. CLEAR the DTC. TEST the system for normal operation.

CHECK TRANSMISSION RANGE SENSOR CONTINUITY IN 2 (TO VIN D15361).
1. Select 2.
2. Check for continuity between pins 08 and 03 of the sensor.
^ Is the circuit continuous?
-> Yes
-> No
Carry out the adjustment procedure for the transmission range sensor. Recheck the circuit. If still open circuit, INSTALL a new transmission range sensor. CLEAR the DTC. TEST the system for normal operation.

CHECK TRANSMISSION RANGE SENSOR CONTINUITY IN 3 (TO VIN D15361).
1. Select 3.
2. Check for continuity between pins 08 and 04 of the sensor.
^ Is the circuit continuous?
-> Yes
-> No
Carry out the adjustment procedure for the transmission range sensor. Recheck the circuit. If still open circuit, INSTALL a new transmission range sensor. CLEAR the DTC. TEST the system for normal operation.

CHECK TRANSMISSION RANGE SENSOR GROUND CIRCUIT.
1. Measure the resistance between JB156, pin 08 (B) and GROUND.
^ Is the resistance greater than 5 ohms?
-> Yes
REPAIR the high resistance circuit.
-> No

CHECK TRANSMISSION RANGE SENSOR PARK SIGNAL WIRE FOR CONTINUITY.
1. Disconnect the TOM electrical connector JB131.
2. Measure the resistance between JB131, pin 30 (U) and the TR sensor electrical connector JB156, pin 09 (U).
^ Is the resistance greater than 5 ohms?
-> Yes
REPAIR the high resistance circuit.
-> No

CHECK TRANSMISSION RANGE SENSOR REVERSE SIGNAL WIRE FOR CONTINUITY.
1. Measure the resistance between JB131, pin 26 (G) and JB156, pin 07 (G).
^ Is the resistance greater than 5 ohms?
REPAIR the high resistance circuit.
-> No

CHECK TRANSMISSION RANGE SENSOR NEUTRAL SIGNAL WIRE FOR CONTINUITY.
1. Measure the resistance between JB131, pin 25 (W) and JB156, pin 02(W).
^ Is the resistance greater than 5 ohms?
REPAIR the high resistance circuit.
-> No

CHECK TRANSMISSION RANGE SENSOR DRIVE SIGNAL WIRE FOR CONTINUITY.
1. Measure the resistance between JB131, pin 27 (Y) and JB156, pin 01 (Y).
^ Is the resistance greater than 5 ohms?
REPAIR the high resistance circuit.
-> No

CHECK TRANSMISSION RANGE SENSOR 2 SIGNAL WIRE FOR CONTINUITY (TO VIN D15361).
1. Measure the resistance between JB131, pin 08 (r) and JB156, pin 03 (r).
^ Is the resistance greater than 5 ohms?
REPAIR the high resistance circuit.
-> No

CHECK TRANSMISSION RANGE SENSOR 3 SIGNAL WIRE FOR CONTINUITY (TO VIN D15361).
1. Measure the resistance between JB131, pin 07 (0) and JB156, pin 04 (O).
^ Is the resistance greater than 5 ohms?
REPAIR the high resistance circuit.
-> No
INSTALL a new TCM. CLEAR the DTC. TEST the system for normal operation.