B0135

SUPPLEMENTAL RESTRAINT SYSTEM: AIRBAG SYSTEM: B0135/73: Short in Front Pretensioner Squib LH Circuit

DTC B0135/73 - Short in Front Pretensioner Squib LH Circuit

DESCRIPTION

The front pretensioner squib LH circuit consists of the center airbag sensor assembly and the front seat outer belt assembly LH (front pretensioner squib LH).
This circuit instructs the SRS to deploy when deployment conditions are met.
DTC B0135/73 is recorded when a short circuit is detected in the front pretensioner squib LH circuit.






WIRING DIAGRAM





INSPECTION PROCEDURE
HINT:
- Perform the simulation method by selecting the "check mode" (signal check) with the Techstream Check Mode Procedure.
- After selecting the "check mode" (signal check), perform the simulation method by wiggling each connector of the airbag system or driving the vehicle on a city or rough road Check Mode Procedure.

PROCEDURE

1. CHECK FRONT SEAT OUTER BELT ASSEMBLY LH (FRONT PRETENSIONER SQUIB LH)




(a) Turn the ignition switch to the LOCK position.
(b) Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.
(c) Disconnect the connectors from the front seat outer belt assembly LH.
(d) Connect the white wire side of SST (resistance 2.1 Ohms) to the floor wire No. 2.
CAUTION:
Never connect a tester to the front seat outer belt assembly LH (front pretensioner squib LH) for measurement, as this may lead to a serious injury due to airbag deployment.
NOTE:
Do not forcibly insert the SST into the terminals of the connector when connecting.

Insert the SST straight into the terminals of the connector.
SST: 09843-18060
(e) Connect the negative (-) terminal cable to the battery, and wait for at least 2 seconds.
(f) Turn the ignition switch to the ON position, and wait for at least 60 seconds.
(g) Clear the DTCs stored in memory DTC Check / Clear.
(h) Turn the ignition switch to the LOCK position.
(i) Turn the ignition switch to the ON position, and wait for at least 60 seconds.
(j) Check the DTCs DTC Check / Clear.
OK:
DTC B0135/73 is not output.
HINT: Codes other than DTC B0135/73 may be output at this time, but they are not related to this check.

NG -- CHECK CONNECTOR
OK -- REPLACE FRONT SEAT OUTER BELT ASSEMBLY LH
2. CHECK CONNECTOR
(a) Turn the ignition switch to the LOCK position.
(b) Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.
(c) Disconnect the SST (resistance 2.1 Ohms) from the floor wire No. 2.
(d) Check that the floor wire No. 2 connector (on the front seat outer belt assembly LH side) is not damaged.
OK:
The lock button is not disengaged, and the claw of the lock is not deformed or damaged.
NG -- REPAIR OR REPLACE FLOOR WIRE NO. 2
OK -- Continue to next step.
3. CHECK FLOOR WIRE NO. 2 (FRONT PRETENSIONER SQUIB LH)




(a) Disconnect the connector from the center airbag sensor assembly.
(b) Release the activation prevention mechanism built into connector "B" Diagnosis System.
(c) Measure the resistance according to the value(s) in the table below.
Standard resistance:






NG -- REPAIR OR REPLACE FLOOR WIRE NO. 2
OK -- Continue to next step.
4. CHECK CENTER AIRBAG SENSOR ASSEMBLY




(a) Connect the connectors to the front seat outer belt assembly LH and the center airbag sensor assembly.
(b) Connect the negative (-) terminal cable to the battery, and wait for at least 2 seconds.
(c) Turn the ignition switch to the ON position, and wait for at least 60 seconds.
(d) Clear the DTCs stored in memory DTC Check / Clear.
(e) Turn the ignition switch to the LOCK position.
(f) Turn the ignition switch to the ON position, and wait for at least 60 seconds.
(g) Check the DTCs DTC Check / Clear.
OK:
DTC B0135/73 is not output.
HINT: Codes other than DTC B0135/73 may be output at this time, but they are not related to this check.

NG -- REPLACE CENTER AIRBAG SENSOR ASSEMBLY
OK -- USE SIMULATION METHOD TO CHECK