Troubleshooting
DTC P2197 OXYGEN SENSOR SIGNAL STUCK LEAN (BANK 2 SENSOR 1)CIRCUIT DESCRIPTION
DTC Detecting Condition:
To obtain a high purification rate of the CO, HC and NOx components of the exhaust gas, a three-way catalytic converter is used. For the most efficient use of the three-way catalytic converter, the air-fuel ratio must be precisely controlled so that it is always close to the stoichiometric air-fuel ratio.
The air fuel ratio sensor has the characteristic that it provides output voltage* being approximately proportional to the existing air-fuel ratio. The air fuel ratio sensor output voltage* is used to provide feedback for the ECM to control the air-fuel ratio.
By the air fuel ratio sensor output, the ECM can determine the deviation amount from the stoichiometric air-fuel ratio and control the proper injection time immediately. If the air fuel ratio sensor is does not function, ECM is unable to perform the accurate air-fuel ratio control.
The air fuel ratio sensor is equipped with a heater which heats the zirconia element. The heater is controlled by the ECM. When the intake air volume is low (the temperature of the exhaust gas is low), the current flows to the heater to heat the sensor for the accurate oxygen concentration detection.
*: The voltage value changes at the inside of the ECM only.
HINT:
- This DTC is recorded when air fuel ratio sensor heater is in a malfunction, although the caption is oxygen sensor.
- DTCs P2195 and P2196 means malfunction related to bank 1 air fuel ratio sensor circuit.
- DTCs P2197 and P2198 means malfunction related to bank 2 air fuel ratio sensor circuit.
- Bank 1 refers to the bank that includes cylinder No.1.
- Bank 2 refers to the bank that includes cylinder No.2.
- Sensor 1 refers to the sensor closest to the engine body.
- After confirming DTC P2195, P2196, P2197 and P2198 use the OBD II scan tool or the hand-held tester to confirm voltage output of A/F sensor (AFS B1 S1/AFS B2 S1) from the "DIAGNOSIS/ENHANCED OBD II/DATA LIST/ALL DATA.
- The air fuel ratio sensors output voltage and the short-term fuel trim value can be read using the OBD II scan tool or the hand-held tester.
- The ECM controls the voltage of the AFR+, AFL+, AFR- and AFL- terminals of the ECM to the fixed voltage. Therefore, it is impossible to confirm the air fuel ratio sensor output voltage without the OBD II scan tool or the hand-held tester.
- The OBD II scan tool (excluding hand-held tester) displays the one fifth of the air fuel ratio sensor output voltage which is displayed on the hand-held tester.
Wiring Diagram:
CONFIRMATION DRIVING PATTERN
1. Connect the hand-held tester to the DLC3. (*1)
2. Switch the hand-held tester from the normal mode to the check mode.(*1)
3. Start the engine and warm it up with all the accessory switches OFF.(*2)
4. Drive the vehicle at 60 - 120 km/h (38 - 75 mph) and engine speed at 1,400 - 3,200 rpm for 3 - 5 min.(*3)
HINT: If a malfunction exists, the MIL will light up during step. (*3)
NOTE: If the conditions in this test are not strictly followed, detection of the malfunction will not be possible.
If you do not have a hand-held tester, turn the ignition switch OFF after performing steps (*2) and (*3), then perform steps (*2) and (*3) again.
Step 1:
Step 2:
Step 2 (continued) - 4:
Step 5:
Step 6 - 10:
Step 11 - 16:
Step 17 - 18:
INSPECTION PROCEDURE
HINT:
Hand-held tester only:
The narrowing down the trouble area is possible by performing ACTIVE TEST of the following "A/F CONTROL" (oxygen sensor or another can be distinguished).
a. Perform ACTIVE TEST by hand-held tester (A/F CONTROL).
HINT: "A/F CONTROL" is an ACTIVE TEST which changes the injection volume to -12.5% or +25%.
1. Connect the hand-held tester to the DLC3 on the vehicle.
2. Turn the ignition switch ON.
3. Warm up the engine with the engine speed at 2,500 rpm for approx. 90 sec.
4. Select the item "DIAGNOSIS/ENHANCED OBD II/ACTIVE TEST/ A/F CONTROL".
5. Perform "A/F CONTROL" when idle condition (press the right or left button).
Result:
Air fuel ratio sensor and oxygen sensor reacts in synchronizing with increase and decrease of injection volume (+25% rich output: 1 V, -12.5% lean output: 0 V)
NOTE: However, there is a few second delay in the sensor 1 (front air fuel ratio sensor) output. And there is about 20 seconds delay in the sensor 2 (rear oxygen sensor).
The following procedure of A/F CONTROL enable that to check its output (show its graph indication) of air fuel ratio sensor and oxygen sensor.
To display the graph indication. Select and push the "YES or NO" button 2 data "AFS B1 S1 and O2S B1 S2" or "AFS B2S1 and O2S B2S2" and press button "4" after selecting "ACTIVE TEST/ A/F CONTROL/USER DATA".
HINT:
- If DTC P2195 or P2196 is displayed, check bank 1 sensor 1 circuit.
- If DTC P2197 or P2198 is displayed, check bank 2 sensor 1 circuit.
- Read freeze frame data using the hand-held tester or the OBD II scan tool, as freeze frame data records the engine conditions when a malfunction is detected. When troubleshooting, it is useful for determining whether the vehicle was running or stopped, the engine was warmed up or not, the air-fuel ratio was lean or rich, etc. at the time of the malfunction.
CHECK FOR INTERMITTENT PROBLEMS
Hand-held tester only:
By putting the vehicle's ECM in the check mode, the 1 trip detection logic is possible instead of 2 trip detection logic and sensitivity the to detect open circuits is increased. This makes it easier to detect intermittent problems.
1. Clear the DTC.
2. Set the check mode.
3. Perform a simulation test.
4. Check the connector and terminal.
5. Handle the connector.