Front
FRONT BRAKECOMPONENTS (Part 1):
COMPONENTS (Part 2):
DISASSEMBLY
1. REMOVE FRONT BRAKE PAD
(a) Remove the 2 anti-squeal springs.
(b) Remove the 2 brake pads from the front disc brake cylinder mounting.
2. REMOVE FRONT ANTI-SQUEAL SHIM
(a) Remove the 2 anti-squeal shims and the 2 pad wear indicators from each pad.
3. REMOVE FRONT DISC BRAKE PAD SUPPORT PLATE
(a) Remove the 4 front disc brake pad support plates from the front disc brake cylinder mounting.
4. REMOVE FRONT DISC BRAKE CYLINDER MOUNTING
(a) Remove the 2 bolts and front disc brake cylinder mounting from the steering knuckle.
5. REMOVE NO. 1 FRONT DISC BRAKE CYLINDER SLIDE PIN
(a) Remove the No. 1 front disc brake cylinder slide pin from the front disc brake cylinder mounting.
6. REMOVE NO. 2 FRONT DISC BRAKE CYLINDER SLIDE PIN
(a) Remove the No. 2 front disc brake cylinder slide pin from the front disc brake cylinder mounting.
7. REMOVE FRONT DISC BRAKE CYLINDER SLIDE BUSHING
(a) Using a screwdriver, remove the front disc brake cylinder slide bushing from the No. 2 front disc brake cylinder slide pin.
NOTICE: Do not damage the No. 2 front disc brake cylinder slide pin.
HINT: Tape the screwdriver tip before use.
8. REMOVE FRONT DISC BRAKE BUSHING DUST BOOT
(a) Remove the 2 front disc brake bushing dust boots from the front disc brake cylinder mounting.
9. REMOVE CYLINDER BOOT
(a) Using a screwdriver, remove the cylinder boot set ring and the cylinder boot.
NOTICE: Be careful not to damage the brake piston and cylinder.
10. REMOVE FRONT DISC BRAKE PISTON
(a) Prepare a wooden plate to hold the front disc brake piston.
(b) Place the wooden plate between the front disc brake piston and the disc brake cylinder assembly.
(c) Use compressed air to remove the front disc brake piston from the disc brake cylinder assembly.
CAUTION: Do not place your fingers in front of the front disc brake piston when using compressed air.
NOTICE: Do not spatter the brake fluid.
11. REMOVE PISTON SEAL
(a) Using a screwdriver, remove the piston seal from the disc brake cylinder assembly.
NOTICE: Do not damage the inner cylinder or cylinder groove.
HINT: Tape the screwdriver tip before use.
12. REMOVE FRONT DISC BRAKE BLEEDER PLUG CAP
13. REMOVE FRONT DISC BRAKE BLEEDER PLUG
14. REMOVE FRONT DISC
(a) Remove the front disc.
HINT: Put matchmarks on the disc and the axle hub.
REASSEMBLY
1. INSTALL FRONT DISC
(a) Align the matchmarks and install the front disc.
NOTICE: When replacing the disc with a new one, select the installation position where the front disc has the minimum runout.
2. TEMPORARILY TIGHTEN FRONT DISC BRAKE BLEEDER PLUG
(a) Temporarily tighten the front disc brake bleeder plug to the disc brake cylinder sub-assembly.
3. INSTALL FRONT DISC BRAKE BLEEDER PLUG CAP
(a) Install the bleeder plug cap to the front disc brake bleeder plug.
4. INSTALL PISTON SEAL
(a) Apply lithium soap base glycol grease to a new piston seal.
(b) Install the piston seal to the disc brake cylinder assembly.
5. INSTALL FRONT DISC BRAKE PISTON
(a) Apply lithium soap base glycol grease to the front disc brake piston and a new cylinder boot.
(b) Install the cylinder boot to the front disc brake piston.
(c) Install the front disc brake piston to the disc brake cylinder assembly.
NOTICE: Do not install the front disc brake piston forcibly in the disc brake cylinder assembly.
6. INSTALL CYLINDER BOOT
(a) Install the cylinder boot to the disc brake cylinder assembly.
NOTICE: Install the boot securely to the grooves of the cylinder and piston.
(b) Using a screwdriver, install a new cylinder boot set ring.
NOTICE:
^ Install the cylinder boot set ring securely to the grooves of the cylinder boot.
^ Do not damage the cylinder boot.
HINT: Tape the screwdriver tip before use.
7. INSTALL FRONT DISC BRAKE BUSHING DUST BOOT
(a) Apply lithium soap base glycol grease to the seal surface of 2 new front disc brake bushing dust boots.
(b) Install the 2 front disc brake bushing dust boots to the front disc brake cylinder mounting.
8. INSTALL FRONT DISC BRAKE CYLINDER SLIDE BUSHING
(a) Apply lithium soap base glycol grease to a new front disc brake cylinder slide bushing.
(b) Install the front disc brake cylinder slide bushing to the No. 2 front disc brake cylinder slide pin.
9. INSTALL NO. 2 FRONT DISC BRAKE CYLINDER SLIDE PIN
(a) Apply the lithium soap base glycol grease to the sliding part and the seal surface of the No. 2 front disc brake cylinder slide pin.
(b) Install the No. 2 front disc brake cylinder slide pin to the bottom side of the front disc brake cylinder mounting.
10. INSTALL NO. 1 FRONT DISC BRAKE CYLINDER SLIDE PIN
(a) Apply the lithium soap base glycol grease to the sliding part and the seal surface of the No. 1 front disc brake cylinder slide pin.
(b) Install the No. 1 front disc brake cylinder slide pin.
11. INSTALL FRONT DISC BRAKE CYLINDER MOUNTING
(a) Install the front disc brake cylinder mounting to the steering knuckle with the 2 bolts.
Torque: 107 N*m (1,090 kgf*cm, 79 ft.*lbf)
12. INSTALL FRONT DISC BRAKE PAD SUPPORT PLATE
(a) Install the front disc brake pad support plate to the front disc brake cylinder mounting.
13. INSTALL FRONT ANTI-SQUEAL SHIM
(a) Apply disc brake grease to the front anti-squeal shim.
NOTICE:
^ When replacing worn pads, the front anti-squeal shim must be replaced together with the pad.
^ Install the shim in the correct positions and directions.
^ Apply disc brake grease to the area that contacts the front anti-squeal shim.
^ Disc brake grease can come out slightly from the area where the front anti-squeal shim is installed.
^ Make sure that disc brake grease is not applied onto the lining surface.
(b) Install the 2 front anti-squeal shims and the 2 pad wear indicators to each pad.
NOTICE: Install the shims in the correct positions and directions.
NOTICE: Install the pad wear indicator in the correct positions and directions.
14. INSTALL FRONT BRAKE PAD
(a) Install the 2 front brake pads with front anti-squeal shim to the front disc brake cylinder mounting.
(b) Install the 2 anti-squeal springs.