P202E

M16/6 (Throttle valve actuator) (P0120)

Test 1: Check component M16/6 (Throttle valve actuator).

1. Check component M16/6 (Throttle valve actuator).

Test 1.1: Check component M16/6 (Throttle valve actuator) using actual value.

Test 1.2: Actuate component M16/6m1 (Actuator motor).

Test 1.3: Check internal resistance of component M16/6m1 (Actuator motor).

Test 1.4: Test series resistance of actual value potentiometers of component M16/6m1 (Actuator motor).

Test 1.5: Test voltage supply of the potentiometers of component M16/6 (Throttle valve actuator).

1.1. Check component M16/6 (Throttle valve actuator) using actual value.
Test prerequisite

- The engine is running.
Status of the relevant actual values:
- M16/6 (Throttle valve actuator) Signal 1:Warning! Communication with ECU required.
- M16/6 (Throttle valve actuator) Signal 2:Warning! Communication with ECU required.
Specified values

- M16/6 (Throttle valve actuator)Signal 1(Idle speed): [0.30...0.90] V
- M16/6 (Throttle valve actuator)Signal 2(Idle speed): [4.00...4.60] V
- M16/6 (Throttle valve actuator)Signal 1(Full load):[4.00...4.60] V
- M16/6 (Throttle valve actuator)Signal 2(Full load):[0.30...0.90] V
Question

- Are the actual values o.k.?


YES
The actual values are okay.End of test

NO
At least one of the relevant actual values is not okay.Possible cause and remedy

- Test series resistance of actual value potentiometers of component M16/6m1 (Actuator motor).
- Check power supply of component M16/6 (Throttle valve actuator).


1.2. Actuate component M16/6m1 (Actuator motor).
Warning!Communication with ECU required.


1.3. Check internal resistance of component M16/6m1 (Actuator motor).
Test prerequisite

- The actual values are not okay.
Test sequence

- Switch off ignition.
- Disconnect coupling 1 at component N3/10 (ME-SFI [ME] control unit).
- (N3/10) 1.Measure resistance with multimeter between sockets 6 and 1.3 (N3/10)
Specified value

- Resistor[1...10]ohms
Question

- Is the measurement value OK?


YES
The measurement value is OK.End of test

NO
The measurement value is not OK.Possible cause and remedy

- Lines between N3/10 (ME-SFI [ME] control unit) and M16/6m1 (Actuator motor)
- M16/6m1 (Actuator motor)


1.4. Test series resistance of actual value potentiometers of component M16/6m1 (Actuator motor).
Test prerequisites

- At least one of the relevant actual values is not okay.
Test sequence

- Switch off ignition.
- Disconnect coupling 2 at component N3/10 (ME-SFI [ME] control unit).
- (N3/10) 2.Measure resistance with multimeter between sockets 2 and 2.3 (N3/10)
Specified value

- Resistor[1800...2000]ohms
Question

- Is the measurement value OK?


YES
The measurement value is OK.Test prerequisites

- At least one of the relevant actual values is not okay.
- The throttle flap of component M16/6 (Throttle valve actuator) should operate freely and must not stick or rub.
Test sequence

- Switch off ignition.
- Remove component B2/5 (Hot film mass air flow sensor).
- Disconnect coupling 2 at component N3/10 (ME-SFI [ME] control unit).
M16/6r1 (Throttle valve actual value potentiometer)

- (N3/10) 2.Measure resistance with multimeter between sockets 9 and 2.3 (N3/10)
- Slowly operate throttle flap by hand up to full load.
Specified values

- Idle speed[ca. 650]ohms
- Full load[ca. 1490]ohms
M16/6r2 (Drive actual value potentiometer)

- (N3/10) 2.Measure resistance with multimeter between sockets 9 and 2.2 (N3/10)
- Slowly operate throttle flap by hand up to full load.
Specified values

- Idle speed[ca. 1380]ohms
- Full load[ca. 480]ohms
Question

- Are the measurement values OK?


YES
The measurement values are OK.Further possible causes of fault

- Test voltage supply of the potentiometers of component M16/6 (Throttle valve actuator).


NO
The measurement values are not OK.Possible cause and remedy

- Lines to component M16/6 (Throttle valve actuator)
- M16/6 (Throttle valve actuator)


NO
The measurement value is not OK.Possible cause and remedy

- Lines to component M16/6 (Throttle valve actuator)
- M16/6 (Throttle valve actuator)


1.5. Test voltage supply of the potentiometers of component M16/6 (Throttle valve actuator).
Test prerequisite

- At least one of the relevant actual values is not okay.
- The power supply of component N3/10 (ME-SFI [ME] control unit) is OK.
Test sequence

- Switch off ignition.
- Detach coupling at component M16/6 (Throttle valve actuator).
- Measure direct voltage with multimeter between pins (M16/6) 2 and (M16/6) 3
- Switch on ignition.
Specified value

- Voltage[4.75...5.25] V
Question

- Is the measurement value OK?







YES
The measurement value is OK.Further possible causes of fault

- M16/6 (Throttle valve actuator)
End of test

NO
The measurement value is not OK.Possible cause and remedy

- Lines to component M16/6 (Throttle valve actuator)
- N3/10 (ME-SFI [ME] control unit)
End of test