Part 3
36. Wait for both bar graphs to complete.
NOTE:
During the second half of the reprogram, various indicator lamps and information displays in the meter and gauges assembly may flash. This is normal.
37. When the screen in Figure 34 appears, reprogramming is complete.
a. Select Next and wait for System Call to complete.
CAUTION:
If reprogramming does not complete and the !? displays as shown in Figure C:
^ Check battery voltage (12.0 - 15.5V).
^ Ignition is ON, Ready Mode is OFF.
^ External Bluetooth(R) devices are OFF.
^ All electrical loads are OFF.
^ Select Retry and follow the on screen instructions.
^ Retry may not go through on first attempt and can be selected more than once.
OR: If reprogramming does not complete and the X displays as shown in Figure D:
Do not disconnect plus VI or shut down Consult III plus if reprogramming does not complete.
^ Check battery voltage (12.0 - 15.5V).
^ CONSULT A/C adapter is plugged in.
^ Ignition is ON, Ready Mode is OFF.
^ Transmission in Park.
^ All C-III plus / plus VI cables are securely connected.
^ All C-III plus updates are installed.
^ Select Home, and then restart the reprogram procedure from the beginning.
38. Erase all DTCs:
a. Turn "ignition" off by depressing the power switch once.
^ The screen in Figure 35 will read OFF after pressing the power switch once.
b. Turn "ignition" on by depressing the power switch twice.
^ Do not step on the brake pedal when depressing the power switch.
^ The screen in Figure 36 will read ON after pressing the power switch twice.
NOTE:
Do not be confused by any screen messages. At this point, simply turn the "ignition" on.
c. Wait for the bar graph in the ERASE window to complete 100%.
39. Verify the part number has changed.
a. Print a copy by selecting Print.
NOTE:
Before and after part numbers on your print-out may be switched compared to your CONSULT PC screen. This is ok.
b. Attach the copy to the repair order.
c. Once a copy has been printed, select Confirm.
40. After Confirmation has completed, select Home.
41. Close C-III plus by selecting "X" in Figure 39.
^ Do not turn off the CONSULT PC.
42. Place the vehicle in "READY to drive" mode:
^ Apply the parking brake.
^ Depress the brake pedal.
^ Depress the power switch once.
^ The meter and gauges will illuminate.
43. Open C-III plus.
44. Once the plus VI is recognized, select Diagnosis (All Systems).
45. Select LEAF and 2011 or 2012, or Automatic Selection (VIN).
^ If Automatic Selection (VIN) is selected, wait for the Reading VIN screen to complete.
46. Select, Select or Detect Vehicle, whichever displays.
47. Verify the VIN in VIN or Chassis # matches that of the vehicle.
^ If the correct VIN exists, select Confirm.
48. Wait for System Call to complete.
49. If DTCs are present, select ERASE.
^ If no DTCs are present, skip to Step 52.
50. Select ERASE.
51. Select Close.
52. Using the arrow keys, select Page 3/3, and then select HVAC.
53. Select ERASE.
54. Select ERASE.
55. Select Close.
NOTE:
If DTC B2631 (SUNLOAD SENSOR) trips again, this is okay.
56. Select Back.
57. Using the arrow keys, go to Page 3/3, and then select MULTI AV.
58. Select ERASE.
59. Select Erase.
60. Select Close.
61. Once all DTCs have been erased:
a. Select Home, and then on the next screen, select Yes (picture not shown).
b. Close C-III plus, turn off the CONSULT PC, and then disconnect the CONSULT PC and plus VI from the vehicle.
c. Turn "ignition" off (depress power switch once).
62. For vehicles that have the "Battery Heater" option, refer to procedure "Procedure to clear battery heater DTCs" to clear battery heater DTCs.
63. Verify the repair is complete:
a. Place the vehicle in the "READY to drive" mode (press power switch while stepping on the brake pedal).
b. Verify no error messages are displayed in the meter and gauges or center multi-function control panel.
c. If the timer for either charging or climate control was on prior to reprogramming, turn them back on.
OWNER'S MANUAL/TABLE C
64. Replace the vehicle owners manual with latest updated publication.
> Confirm that:
^ The new owner's manual was printed on or after the date in Table C,
then
^ Replace the owner's manual. *