Recall - Reprogram Air Bag Control Module (Canadian)
SAFETYBulletin No.: 11319A
Date: January 06, 2012
Subject: --11319A Front Passenger Airbag Reprogram Sensing and Diagnostic Module
Models:
2008-2009 Pontiac G8
Canadian Vehicles
Supercede:
The Note Statement and instructions for Steps 3 and 4 of the Service Procedure have been revised. Please discard all copies of bulletin 11319, issued November 2011.
Condition
General Motors has decided that a defect, which relates to motor vehicle safety, exists in all2008-2009 model year Pontiac G8 Canadian vehicles. With the front passenger seat positioned full forward, the seat position sensor will cause a 30 millisecond deployment delay between the first and second stages of the dual-stage frontal passenger airbag. In the event of a crash severe enough to command deployment of the front passenger airbag, this delay may result in increased head injury to certain (5th percentile) front seat occupants.
Correction
Dealers are to reprogram the Sensing and Diagnostic Module.
Vehicles Involved
Involved are all 2008-2009 model year Pontiac G8 Canadian vehicles.
Important
Dealers are to confirm vehicle eligibility prior to beginning repairs by using the Required Field Actions section in the Global Warranty system. Not all vehicles may be involved.
For dealers with involved vehicles, a listing with involved vehicles containing the complete vehicle identification number, customer name, and address information has been prepared and will be provided to dealers through the GM GlobalConnect Recall Reports. Dealers will not have a report available if they have no involved vehicles currently assigned.
The listing may contain customer names and addresses obtained from Motor Vehicle Registration Records. The use of such motor vehicle registration data for any purpose other than follow-up necessary to complete this recall is a violation of law in several states/provinces/countries. Accordingly, you are urged to limit the use of this report to the follow-up necessary to complete this recall.
Parts Information
No parts are required for this recall.
Service Procedure
Do not attempt to order the calibration number from GM Customer Care and Aftersales. The calibration numbers required for this service procedure are programmed into control modules via a Multiple Diagnostic Interface (MDI) or Tech 2 with the calibration update. When using a MDI or Tech 2 for reprogramming, ensure that it is updated with the latest software version. Use TIS2WEB on or after 11/22/11 to obtain the calibration. If you cannot access the calibration, call the Techline Customer Support Center and it will be provided.
For step-by-step programming instructions, please refer to SI and the Techline Information System (TIS) terminal.
1. Verify that there is a battery charge of 12 to 15 volts. The battery must be able to maintain a charge during programming. Only use an approved Midtronics(R) PSC 550 Battery Maintainer (SPS Programming Support Tool EL-49642) or equivalent to maintain proper battery voltage during programming.
2. Reprogram the inflatable restraint and sensing diagnostic module (SDM). Refer to SI and Service Programming System (SPS) documentation for programming instructions, if required.
1. Connect the MDI or Tech 2 to the vehicle.
2. Select J2534 MDI or J2534 Tech 2 and Reprogram ECU from the Select Diagnostic Tool and Programming Process screen.
3. Select SDM Inflatable Restraint Sensing and Diagnostic Module -- Programming from the Supported Controllers screen.
4. Follow the on-screen instructions.
Note
The air bag indicator light may begin flashing or remain ON after the body control module (BCM), or inflatable restraint sensing and diagnostic module (SDM) is reprogrammed or replaced, and during the programming procedure for the BCM or SDM until after the procedure is completed. When installing a new SDM, there may be several DTCs set prior to programming. Once programmed, these DTCs should be in history and can be cleared.
3. Using the scan tool, select the SDM Module Setup menu, then select Setup SDM Primary Key in BCM. Follow the scan tool on-screen instructions.
Note
The airbag telltale will continue to flash until Step 4 is completed.
4. Ignition ON, using the scan tool, select the SDM Module Setup menu, then select Setup New SDM. Follow the scan tool on-screen instructions.
5. Clear all diagnostic trouble codes (DTCs).
Courtesy Transportation
The General Motors Courtesy Transportation program is intended to minimize customer inconvenience when a vehicle requires a repair that is covered by the New Vehicle Limited Warranties. The availability of courtesy transportation to customers whose vehicles are within the warranty coverage period and involved in a product program is very important in maintaining customer satisfaction. Dealers are to ensure that these customers understand that shuttle service or some other form of courtesy transportation is available and will be provided at no charge. Dealers should refer to the General Motors Service Policies and Procedures Manual for Courtesy Transportation guidelines.
Warranty Transaction Information
Submit a transaction using the table below.
Customer Notification
General Motors will notify customers of this recall on their vehicle (see copy of customer letter included with this bulletin).
Dealer Recall Responsibility
All unsold new vehicles in dealers' possession and subject to this recall must be held and inspected/repaired per the service procedure of this recall bulletin before customers take possession of these vehicles.
Dealers are to service all vehicles subject to this recall at no charge to customers, regardless of mileage, age of vehicle, or ownership, from this time forward.
Customers who have recently purchased vehicles sold from your vehicle inventory, and for which there is no customer information indicated on the dealer listing, are to be contacted by the dealer. Arrangements are to be made to make the required correction according to the instructions contained in this bulletin. A copy of the customer letter is provided in this bulletin for your use in contacting customers. Recall follow-up cards should not be used for this purpose, since the customer may not as yet have received the notification letter.
In summary, whenever a vehicle subject to this recall enters your vehicle inventory, or is in your dealership for service in the future, you must take the steps necessary to be sure the recall correction has been made before selling or releasing the vehicle.
Disclaimer