Removing and Installing Panel of Panoramic Roof
Removing And Installing Panel Of Panoramic Roof
Tools
Removing panel of panoramic roof
Removing panel 1 of panoramic roof
1. Fully open panels 1 and 2 of panoramic roof
2. Unclip cover -16- (-Arrow A-) and pull out to the rear (-Arrow B-).
3. Unscrew fastening screws -7- and lay air deflector aside -5-.
4. Unscrew fastening screw -8- at end stop -9-.
5. Unscrew fastening screw -10- of front mount -11-.
6. Press guide -12- gently outwards (-Arrow A-), disengage stop -13- together with guide pin from the guide -12- and remove panel -1- (-Arrow B-).
7. Remove plastic washer -14- from guide pin.
Removing panel 2 of panoramic roof
1. Fully open panel 3 of panoramic roof.
2. Move panel 2 of panoramic roof to tilting position.
3. Undo fastening screws -6-.
4. Remove panel -2- of panoramic roof.
Removing panel 3 of panoramic roof
1. Move panel 3 of panoramic roof to ventilation position.
2. Move panel 2 of panoramic roof to tilting position.
3. Undo fastening screws -6-.
4. Press air deflector -7- to the front (-Arrow A-) and remove together with panel -3- of panoramic roof.
Removing rear wind deflector
1. Swing air deflector -7- together with the spring -8- outwards in a downward direction.
2. Remove plastic washer -9-.
3. Twist spring -8- (-Arrow A-) and remove from bolt of air deflector -7-.
Installing panel of panoramic roof
Installing rear wind deflector
1. Push and twist spring -8- onto bolt of air deflector -7- (-Arrow A-).
2. Push on plastic washer -9-.
3. Position air deflector -7- together with the spring -8- and swing in upwards.
Installing panel 3 of panoramic roof
1. Insert panel -3- of panoramic roof and engage air deflector -7- on the fixed panel -4-.
2. Screw in fastening screws -6- and tighten so that panel 3 of panoramic roof can still be moved easily.
3. Fully close panels 2 and 3 of panoramic roof and check adjustment of panel 3, correcting if necessary. Adjusting panel of panoramic roof.
Installing panel 2 of panoramic roof
1. Insert panel -2- of panoramic roof.
2. Screw in fastening screws -6- and tighten so that panel 2 of panoramic roof can still be moved easily.
3. Fully close panels 2 and 3 of panoramic roof and check adjustment of panel 2, correcting if necessary. Adjusting panel of panoramic roof.
Installing panel 1 of panoramic roof
1. Push plastic washer -14- onto guide pin of stop -13-.
2. Insert panel -1-.
3. Press guide -12- gently outwards (-Arrow A-) and engage stop -13- together with guide pin in the guide -12- (-Arrow B-).
4. Counter front bearing -11-, screw in fastening screw -10- and tighten so that panel 1 of panoramic roof can still be moved easily.
5. Position end stop -9-, counter, screw in fastening screw -8- and tighten so that panel 1 of panoramic roof can still be moved easily.
6. Position air deflector -5-, screw in fastening screws -7- and tighten to the specified tightening torque. Tightening torque 2 ftlb. +/- 0.5 ftlb.
7. Fully close panels 1 and 2 of panoramic roof and check adjustment of panel 1, correcting if necessary. Adjusting panel of panoramic roof.
8. Insert cover guide -16- into mounting -15- and slide it in (-Arrow A-).
9. Clip in cover -16- (-Arrow B-).
10. Fully open panels 1 and 2 of panoramic roof.
Adjusting panel of panoramic roof
Adjusting panel 1 of panoramic roof
1. Adjust height -X- of panel -1- of panoramic roof at front.
Adjustment value 0 mm -1 mm.
2. Tighten fastening screws -10- to the specified tightening torque.
Tightening torque 3 ftlb +/-0.5 ftlb.
3. Adjust height -Y- of panel -1- of panoramic roof at rear.
Adjustment value 0 mm +1 mm.
4. Tighten fastening screw -8A- to specified tightening torque.
Tightening torque 3 ftlb. +/-0.5 ftlb.
5. If necessary, also unscrew fastening screw -8B-, adjust height -Y- and tighten fastening screw -8B- to specified tightening torque.
Tightening torque 3 ftlb. +/-0.5 ftlb.
Adjusting panel 2 of panoramic roof
1. Adjust height -X- of panel -2- of panoramic roof at front.
Adjustment value 0 mm -1 mm.
2. Tighten fastening screw -6A- to specified tightening torque.
Tightening torque 3 ftlb. +/-0.5 ftlb.
3. Adjust height -Y- of panel -2- of panoramic roof at rear.
Adjustment value 0 mm +1 mm
4. Tighten fastening screw -6B- to specified tightening torque.
Tightening torque 3 ftlb. +/-0.5 ftlb.
5. Tighten fastening screw -6C- to specified tightening torque.
Tightening torque 3 ftlb. +/-0.5 ftlb.
Adjusting panel 3 of panoramic roof
1. Adjust height -X- of panel -3- of panoramic roof at front.
Adjustment value 0 mm -1 mm.
2. Tighten fastening screw -6A- to specified tightening torque.
Tightening torque 3 ftlb. +/-0.5 ftlb.
3. Adjust height -Y- of panel -3- of panoramic roof at rear.
Adjustment value 0 mm +1 mm.
4. Tighten fastening screw -6B- to specified tightening torque.
Tightening torque 3 ftlb. +/-0.5 ftlb.
5. Tighten fastening screw -6C- to specified tightening torque.
Tightening torque 3 ftlb. +/-0.5 ftlb.
Replacing seal for panel of panoramic roof
1. Pull protective paper off adhesive film -10-.
2. Centre adhesive film -10- evenly over the joint and affix to frame from below.
3. Using sealant Terosstat 9220 00000, apply a sealing bead -11- on the adhesive film -10-.
4. Turn over the adhesive film -10- and place it on the sealing bead -11-from above.
5. Press down evenly on the adhesive film -10-.