S9.10 - X - Tools
9.10 X - Tools
S 9.10.1Standohyd(R) Cleaner
S 9.10.1.1 Processing
S 9.10.2Standox(R) Basecoat, colorless
S 9.10.2.1 Processing
S 9.10.3Standohyd(R) Stone Chip Primer
S 9.10.3.1 Application on a textured surface
S 9.10.3.2 Application on a smooth surface
S 9.10.4Standoflex(R) Pore Filler
S 9.10.4.1 Processing
S 9.10.1 Standohyd(R) Cleaner
WARNING: -> 2 "Safety regulations" and read the product-specific safety instructions on the container labels.
Description:
- Water-based cleaner for sanded paint finishes and filled areas
Properties:
- Mild odor
- Reduced solvent emission
Base surfaces:
- Hardened paintwork, sanded
- Standox(R) 2K Nonstop Primer Filler
- Standox(R) 2K Universal Filler
- Standohyd(R) 1K Primer Surfacer
NOTE:
- Raw material base: Water and organic solvents
- Flash point: 41° C/105.8° F
- Spec. weight: 0.96 g/cm3
- Do not allow Standohyd(R) Cleaner to dry on the surface.
- Change cloths in good time
- Collect left-overs from water-dilutable products separately from left-overs from conventional products.
VOC value:
- 155 g/l
S 9.10.1.1 Processing
S 9.10.2 Standox(R) Basecoat, colorless
WARNING: -> 2 "Safety regulations" and read the product-specific safety instructions on the container labels.
Description:
- Substance for repair-painting and spot repairs using conventional basecoat
Properties:
- Material-specific properties
Base surfaces:
- Blends in transition areas in the basecoat creep zone
- Absorbs spray mist in the edge zone
NOTE:
- Raw material base: Physically-drying special resin
- Flash point: 25° C/77° F
- Spec. weight: 0.87 g/cm3
- Solid content: 8.0% weight/5.8% vol.
- Theoretical yield: 7.0 m2/ltr. with a dry coat thickness of 10 microns
- Clean equipment after use with cleaning thinner
VOC value:
- 800 g/l
S 9.10.2.1 Processing
NOTE:
- Supplied ready to spray.
- Further details: -> S 7 "Spot-repair procedures" and -> S 8.1 "Spot repair".
S 9.10.3 Standohyd(R) Stone Chip Primer
WARNING: -> 2 "Safety regulations" and read the product-specific safety instructions on the container labels.
Description:
- Highly-elastic stone chip primer
Properties:
- Water-dilutable
- Can be painted over
- Can be sprayed textured or smooth
Base surfaces:
- Hardened paintwork, sanded
- Primed and filled base surfaces, sanded
- Polystyrene
- Please note base surface pre-treatment instructions:
-> S 5.1
-> S 6.1
-> S 9.2.2
NOTE:
- Raw material base: Water-dispersable copolymer, corrosion inhibition pigments
- Flash point: 99° C/210.2° F
- Spec. weight: 1.34 g/cm3
- Solid content: 63.1% weight/49.8% vol.
- Theoretical yield: 5.0 m2/ltr. with a dry coat thickness of 125 microns
- Rinse equipment before and after use with Standohyd(R) Demineralized Water
- Clean again with cleaning thinner
VOC value:
- 65 g/l
NOTE:
- Do not apply on old coating of underbody sealing.
- Product may not be used on acid primer.
- When you proceed to apply Standohyd(R) Basecoat, allow flash-off time between coats for the water-dilutable basecoat.
- Collect left-overs from water-dilutable products separately from left-overs from conventional products.
- Dispose of cleaning water correctly.
S 9.10.3.1 Application on a textured surface
S 9.10.3.2 Application on a smooth surface
S 9.10.4 Standoflex(R) Pore Filler
WARNING: -> 2 "Safety regulations" and read the product-specific safety instructions on the container labels.
Description:
- Wipe-on filler for filling micro-pores in plastic base surfaces
Properties:
- Easy to apply using wipe-on procedure
- Eliminates "stitched" look
- Only for micro-pores
- Not for bubbled areas
Base surfaces:
- Porous plastics, particularly PUR soft foam
- Please note base surface pre-treatment instructions:
-> S 6.1
-> S 9.2.2
NOTE:
- Raw material base: Special pigment/filler mix, organic solvent
- Flash point: 25° C/77° F
- Spec. weight: 1.72 g/cm3
- Solid content: 77.0% weight/46.5% vol.
- Clean equipment after use with cleaning thinner
VOC value:
- 395 g/l
S 9.10.4.1 Processing
