Part 2
WM 708337 Disassembling and assembling front roof console
Information
- The switch trims can be installed in only one position.
9. Press in the switch trims -arrow A- until you feel the locking tabs -B- engage.
10. Press the bracket carefully to the inside -arrow A-.
11. Place the switch trim in installation position and press it in -arrow B- until it engages securely in the retaining pivot -1-.
Information
- Position the cover in such a way that the sliding switch contacts are pointing towards the shelf.
12. Position the cover in installation position, but do not press down firmly.
13. Position the sliding switch -1- in the cover in such a way that the pictogram is aligned with that on the adjacent switch trims -2-.
14. Turn the cover with the sliding switch around.
15. Insert the holder -1- through the sliding switch -2- ( -arrow A- ) and press it carefully into the bracket -arrow B- until the locking tabs are felt to engage -C-.
16. Connect the contact bridge -c- to the switch -arrow D-.
17. Connect the spring to the sliding switch -a- ( -arrow E- ) until the locking tabs are felt to engage -arrows F-.
18. Place the switch trim in installation position and press it in -arrow A- until the nine locking tabs engage securely -arrows B-.
19. Engage the two covers at the back -A- and press in at the front edge -arrow B- until the locking tabs (three on each cover) are felt to engage -C-. Make sure that the covers are positioned correctly at the frame of the switch trims -D-.
20. Insert the light ring into the cover and align the two markings -arrow-.
21. Align the lighting unit with the sun blind switch -1- and press it in -arrow A- until the locking tabs -B- are felt to engage.
22. Engage the cover at the roof console -C- and press it in -arrow D- until the four locking tabs -E- are felt to engage.
23. Insert the wiring harness into the brackets -arrow-.
24. Connect the two connectors on the printed circuit board until they are felt to engage -arrows A-.
25. Turn the printed circuit board around -arrow B- and screw down with four fastening screws -6-.
26. Connect the connector to the printed circuit board -arrow A- until it engages securely.
27. Turn the printed circuit board around -arrow B- and screw down with three fastening screws -5-.
28. Connect the connector to the printed circuit board until they engage securely -arrow A-.
29. Place the printed circuit board in installation position -arrow B- and screw down with three fastening screws -7-.
30. Insert the microphone -arrow A- until the two locking tabs -B- are felt to engage.
31. Place the reading light in installation position and press it in -arrow A- until the two clips -B- engage securely.
32. Place the switch in installation position and press it in carefully -arrow A-. Make sure that all three locking hooks -B- engage at the switch.
33. Connect the plug connection -arrows A- and slide the piece of plastic foam over the plug connection -arrow B-.
34. Insert the sensor into the roof console frame -A- until the two locking hooks -B- are felt to engage. Ensure it is seated properly.
35. Attach the connector to the printed circuit board -arrow A- until it engages securely.
36. Place the printed circuit board in installation position -arrow B- and screw down with four fastening screws -4-.
Information
- Only if replacing the printed circuit board
37. Insert bulbs into the printed circuit board -arrow A- and tighten -arrow B-.
38. Place the holder in installation position -arrows A- and screw down with three fastening screws -3-.
39. Place the control unit on the holder -arrow B- and screw down with both fastening screws -2-.
40. Push in connector -arrow C- until the locking tabs -D- are felt to engage.
41. Insert the sun visor and holder -2- ( -arrow- ) and secure with the fastening screw -1-.
42. Install front roof console. -> 601219 Removing and installing switch for sunroof - section on "Installing" Service and Repair