Glove Compartment Lock: Service and Repair

WM 681119 Removing and installing glove compartment lock

Removing lock, release and lock cylinder for glove compartment

Removing glove compartment lock





1. Remove trim strip for dashboard on passenger's side. -> 705819 Removing and installing trim strip for dashboard on passenger's side - removing 70581902 Removing and installing trim strip for the dashboard on the passenger's side
2. Remove cover under dashboard on the passenger's side. -> 702219 Removing and installing cover under dashboard - section on "Removing" 702219 Removing and Installing Cover Under Dashboard
3. Remove glove compartment -> 681519 Removing and installing glove compartment - section on "Removing" Service and Repair
4. Remove glove compartment lock.
4.1. Unscrew and remove fastening screw -1-.
4.2. First swivel lock -2- to the right -Arrow A- and then to the front ( -Arrow B- ).





4.3. Remove lock -2- with actuating cable -3- and lock bolt -11- rearward through the dashboard mounting ( -Arrow C- ).





5. Remove actuating cable from lock. -> 681119 Removing and installing glove compartment lock - section on "Removing"

Removing actuating cable for lock





1. Remove glove compartment -> 681519 Removing and installing glove compartment - section on "Removing" Service and Repair
2. Remove glove compartment lock. -> 681119 Removing and installing glove compartment lock - section on "Removing"
3. Remove actuating cable from lock.
3.1. Detach cable -6- from actuating lever -7-. To do this, swivel the cable by approx. 90° to the assembly opening of the actuating lever -Arrow A- and remove it in an upward direction ( -Arrow B- ).





3.2. Compress fixing clips of cable mounting -4- on lock -5- -Arrows C- and pull the cable mounting out of holder ( -Arrow D- ). Remove actuating cable from lock.









4. Remove actuating cable from lock bolt.
4.1. Compress fastening clips -8- of cap -9- towards centre -arrows E- and remove cap.





4.2. Detach cable -6- from actuating lever -12-. To do this, swivel the cable by approx. 90° to the assembly opening of the actuating lever -arrow F- and remove it in an upward direction.





4.3. Compress fastening clips of cable mounting -10- on lock bolt -11- -arrows G- and pull the mounting out of holder ( -arrow H- ). Remove actuating cable on the lock catch bolt.





Removing lock cylinder





1. Remove glove compartment -> 681519 Removing and installing glove compartment - section on "Removing" Service and Repair
2. Remove glove compartment lock. -> 681119 Removing and installing glove compartment lock - section on "Removing"
3. Remove actuating cable from lock. -> 681119 Removing and installing glove compartment lock - section on "Removing"
4. Remove cover.
4.1. Unclip cover -1- from lock mount -2- using a small screwdriver -3- and lift off ( -arrow A- ).









CAUTION

Danger of material damage in the event of incorrect removal and installation of lock cylinder.

- In the event of incorrect removal and installation, the lock cylinder can be damaged.

-> The ignition key must not be withdrawn from the lock cylinder when removing the lock cylinder from or installing it into the lock, as otherwise the spring-loaded locking elements will spring out of the lock barrel.
-> If the ignition key is withdrawn with the lock cylinder removed, the locking elements must be held in on both sides with the fingers until the ignition key is fully out of the lock cylinder. The locking elements can then be carefully relaxed and the lock cylinder laid down.
-> Lock cylinders supplied as spare parts are secured in a transport case.

5. Remove lock barrel.
5.1. Fully insert ignition key -4- into lock cylinder -5- -arrow B-. This locks the locking elements -8- in the lock cylinder.





5.2. Turn ignition key -4- counter-clockwise as far as possible -arrow C- and hold the pretension. This keeps the ignition key tensioned in the lock barrel so that it cannot be withdrawn.





5.3. Force retaining clips -6- of lock cylinder -5- outwards with a small screwdriver ( -arrows D- ).





5.4. Withdraw lock cylinder -5- together with ignition key -4- from the lock -arrow E- and remove.






Installing lock, release and lock cylinder for glove compartment

Installing glove compartment lock





1. Install actuating cable on lock. -> 681119 Removing and installing glove compartment lock - section on "installing"

Information

Once it is fitted correctly on the dashboard mounting, the lock can no longer be moved vertically or to the left or right.

2. Install glove compartment lock.
2.1. Insert lock bolt with actuating cable from the front through the dashboard mounting.
2.2. Insert lock -2- into dashboard mounting -13- -arrow A- and align it until it is resting evenly against the mounting.





2.3. Push lock as far as possible to the left -arrow B- until retaining lugs -15- of lock reach into dashboard mounting -13- on left side.









2.4. Screw in fastening screw -1- and tighten.





3. Install glove compartment. -> 681519 Removing and installing glove compartment - section on "Installing" Service and Repair
4. Install cover under dashboard on passenger's side. -> 702219 Removing and installing trim under dashboard - section on "Installing" 702219 Removing and Installing Cover Under Dashboard
5. Install trim strip for dashboard on passenger's side. -> 705819 Removing and installing dashboard trim strip on passenger's side - section on "Installing" 70581902 Removing and installing trim strip for the dashboard on the passenger's side

Installing actuating cable for lock





1. Install actuating cable on lock.
1.1. Insert traction cable -6- through holder of actuating cable -13- on lock ( -arrow A- ).





1.2. Insert actuating cable -3- on holder -13- of lock ( -arrow A- ). The fastening clips -4- of the traction mounting must engage audibly into the lock holder.





1.3. Attach cable -6- to the assembly opening of actuating lever -7- from above -arrow B- and swivel to the actuating cable holder -13- on the lock ( -arrow C- ).





2. Install actuating cable on lock bolt.
2.1. Insert traction cable -6- through holder of actuating cable -14- on lock bolt ( -Arrow D- ).
2.2. Insert actuating cable -3- on holder -14- of lock bolt ( -Arrow D- ). The fixing clips -10- of the traction mounting must engage audibly into the lock bolt holder.
2.3. Turn actuating lever -12- to the stop in direction of actuating cable holder -14- ( -Arrow E- ).
2.4. Attach cable -6- to the assembly opening of actuating lever -12- from above and swivel to the actuating cable holder -14- on the lock bolt ( -Arrow F- ).





3. Position cap -9- on the lock bolt -11- from above and press in. The fixing clips -9- of the cover must engage audibly.





4. Install glove compartment lock. -> 681119 Removing and installing glove compartment lock - section on "installing"
5. Install glove compartment. -> 681519 Removing and installing glove compartment - section on "Installing" Service and Repair

Installing lock cylinder for lock

CAUTION

Danger of material damage in the event of incorrect removal and installation of lock cylinder.

- In the event of incorrect removal and installation, the lock cylinder can be damaged.

-> The ignition key must not be withdrawn from the lock cylinder when removing the lock cylinder from or installing it into the lock, as otherwise the spring-loaded locking elements will spring out of the lock barrel.
-> If the ignition key is withdrawn with the lock cylinder removed, the locking elements must be held in on both sides with the fingers until the ignition key is fully out of the lock cylinder. The locking elements can then be carefully relaxed and the lock cylinder laid down.
-> Lock cylinders supplied as spare parts are secured in a transport case.





1. Remove transport case.
1.1. Fully insert ignition key -4- into new lock cylinder -5- ( -Arrow A- ).





2. Remove transport case -9- from lock cylinder ( -Arrow B- ).





3. Install lock cylinder.
3.1. Turn actuating lever -7- to the horizontal installation position.





4. Insert lock cylinder -5- together with ignition key -4- into the lock ( -arrow A- ). The release lug of the lock barrel must be pointing to the left.





5. Press lock cylinder -5- into the lock -2- until the retaining clips -6- of the lock cylinder audibly engage.





6. Pull out ignition key -4- from lock cylinder -5- ( -Arrow B- ).





7. Install cover.
7.1. Position cover -1- on the lock carrier -2- and press in -Arrow C- until the retaining clip audibly engages.





8. Install actuating cable on lock. -> 681119 Removing and installing glove compartment lock - section on "installing"
9. Install glove compartment lock. -> 681119 Removing and installing glove compartment lock - section on "installing"
10. Install glove compartment. -> 681519 Removing and installing glove compartment - section on "installing" Service and Repair