Operation CHARM: Car repair manuals for everyone.

69361900 Removing and installing electric adjustment fitting


WM 693619 Removing and installing electric adjustment fitting

Technical values





Preliminary work

1. Remove B-pillar trim. -> 706719 Removing and installing B-pillar trim - "Removing" section 706719 Removing and installing B-pillar trim panel
2. Remove inner sill. -> 680519 Removing and installing inner sill - "Removing" section

Removing electric adjustment fitting

CAUTION

Risk of material damage to support plate with threaded parts in the event of impact with seat belt buckled.

-> When replacing the safety belt following accident damage, the support plate of the adjustment fitting and the threaded parts must also be replaced for safety reasons.





Overview of electric adjustment fitting

1. Unscrew the fastening screws -arrows 1- and remove the holder -arrow A-.





Removing holder and deflection lug

2. Unscrew the fastening nut -arrow 2- and remove the deflection lug -arrow B-.





Removing holder and deflection lug

3. Undo fastening nuts -arrows 3- and remove holder with the plug connections -arrow-.





Removing support

4. Release plug connection -arrow A- and remove it from the clip -arrow B-.





Disconnecting plug connection

5. Release plug -arrow A- and disconnect plug connection -arrows B-.





Disconnecting plug connection

6. Unscrew fastening screws -arrows 4-.





Removing adjustment fitting

7. Unscrew fastening screw -arrow 5- and pull the adjustment fitting upwards -arrow-.





Removing adjustment fitting

8. Press in locking lugs -arrows A- and remove adjusting motor with the shaft -arrow B-.





Removing adjusting motor and shaft

Installing electric adjustment fitting

Information

- Grease the spindle with acid-free grease before assembling the adjustment fitting.





Adjusting motor and shaft

1. Align the spindle -a- with the shaft -b- -arrows A-.





Adjusting motor and shaft

2. Insert the shaft into the adjustment fitting -arrow B- until you feel the locking tabs -arrows C- engage. Turn the spindle -a- slightly, if necessary.





Adjusting motor and shaft

Information

- The fastening screws for the support plate -arrow 5- and adjustment fitting must be replaced following removal for safety reasons.





Fastening screws for support plate and adjustment fitting

3. Engage the adjustment fitting at the bottom -arrow- and tighten at the top with the fastening screw -arrow 5-. => Tightening torque: 3.0 ftlb.





Fastening screws for support plate and adjustment fitting

4. Screw the adjusting motor on securely using the fastening screws -arrows 4-. => Tightening torque: 1.5 Nm (1.0 ftlb.)





Fastening screws for support plate and adjustment fitting

5. Push plug connection together -arrows A- until the locking lug -arrow B- is felt to engage.





Connecting plug connections

6. Push the plug connection onto the clip -arrow C- until you feel the locking hook -arrow D- engage.





Connecting plug connections

7. Position the support in installation position -arrow- and secure with the fastening nuts -arrows 3-. => Tightening torque: 6.0 ftlb.





Installing and tightening support

Information

- Once the fastening nut has been tightened, the deflection lug must level out on its own in a vertical position or in the relevant support direction.





Fitting the deflection lug

Information

- Once the fastening nut has been tightened, the deflection lug must level out on its own in a vertical position or in the relevant support direction.





Fitting the deflection lug

8. Tighten the deflection lug on the adjustment fitting with the fastening nut -arrow 2-. => Tightening torque: 37 ftlb.





Installing deflection lug and holder

9. Screw the holder on securely using the fastening screws -arrows 1-. => Tightening torque: 4.5 Nm (3.0 ftlb.)





Installing deflection lug and holder

Subsequent work

1. Install inner sill. -> 680519 Removing and installing inner sill - "Installing" section
2. Install B-pillar trim. -> 706719 Removing and installing B-pillar trim - "Installing" section 706719 Removing and installing B-pillar trim panel