396119 Removing and Installing Rubber Mounting For Four-Wheel Final Drive
WM 396119 Removing and installing rubber mounting for four-wheel final drive
Tools
Technical values
Preliminary work for rubber mounting on four-wheel final drive
1. Remove four-wheel final drive. -> 398819 Removing and installing four-wheel final drive - "Removing" section 39881900 Removing and installing four-wheel final drive
Removing rubber mounting for four-wheel final drive
Removing rubber mounting for four-wheel final drive, drive side
Rubber mounting, drive side -1-
1. Mark rubber mounting for transmission housing at the installation position -arrow-.
Marking for rubber mounting
2. Position special tool assembly fixture 9716 a/b on rubber mounting => Removing rubber mounting, drive side.
Removing rubber mounting, drive side
3. Remove rubber mounting on drive side -arrow-.
Removing rubber mounting for four-wheel final drive, right output side
Rubber mounting for right output side -2-
1. Mark rubber mounting for transmission housing at the installation position -arrow-.
Marking for rubber mounting
2. Position special tool assembly fixture 9716 a/b on rubber mounting => Removing right rubber mounting.
Removing right rubber mounting
3. Remove rubber mounting in direction of arrow -arrow-.
Removing rubber mounting for four-wheel final drive, left output side
Rubber mounting for left output side -3-
1. Mark rubber mounting for transmission housing at the installation position -arrow-.
Marking for rubber mounting
2. Position special tool assembly fixture 9716 a/b on rubber mounting => Removing left rubber mounting.
Removing left rubber mounting
3. Remove left rubber mounting -arrow-.
Installing rubber mounting for four-wheel final drive
Installing rubber mounting for four-wheel final drive, drive side
Rubber mounting, drive side -1-
Information
Noises in drive line
- Installation position of rubber mounting bulge is incorrect Rubber mounting bulge must be installed vertically into housing
- Installation position of mount in housing is incorrect Pay attention to installation dimension of mount to housing
1. Mark centre of bulge in rubber mounting => Marking for centre of rubber mounting.
Marking for centre of rubber mounting
2. Position rubber mounting in housing using special tool assembly fixture 9716 a/b/c.
3. Pull in rubber mounting in direction of travel until installation position is reached. Measure distance between assembly fixture ring and housing using workshop caliper gauge 139. => Distance: 7.5 mm+/-0.1 mm
Installation position of rubber mounting
Installing rubber mounting for four-wheel final drive, right output side
Rubber mounting for right output side -2-
Information
Noises in drive line
- Installation position of rubber mounting bulge is incorrect Rubber mounting bulge must be installed vertically into housing
- Installation position of mount in housing is incorrect Pay attention to installation dimension of mount to housing
Information
Noises in drive line
- Installation position of rubber mounting bulge is incorrect Rubber mounting bulge must be installed vertically into housing
- Installation position of mount in housing is incorrect Pay attention to installation dimension of mount to housing
1. Mark centre of bulge in rubber mounting => Marking for centre of rubber mounting.
Marking for centre of rubber mounting
2. Position special tool assembly fixture 9716 a/b on rubber mounting.
3. Pull in rubber mounting until installation position is reached.
Installing rubber mounting
4. Rubber mounting must be centred -arrows- in housing.
Installation position of rubber mounting
Installing rubber mounting for four-wheel final drive, left output side
Rubber mounting for left output side -3-
Information
Noises in drive line
- Installation position of rubber mounting bulge is incorrect Rubber mounting bulge must be installed vertically into housing
- Installation position of mount in housing is incorrect Pay attention to installation dimension of mount to housing
Information
Noises in drive line
- Installation position of rubber mounting bulge is incorrect Rubber mounting bulge must be installed vertically into housing
- Installation position of mount in housing is incorrect Pay attention to installation dimension of mount to housing
1. Mark centre of bulge in rubber mounting. -arrows-
Marking for centre of rubber mounting
2. Position special tool assembly fixture 9716 a/b/c on rubber mounting => Positioning bearing.
Positioning bearing
3. Press rubber mounting flush into housing. -direction of arrow-
Subsequent work for four-wheel final drive
Touching up, rubber mounting on four-wheel final drive
1. Install four-wheel final drive. -> 398819 Removing and installing four-wheel final drive - "Installing" section 39881900 Removing and installing four-wheel final drive