Part 1

WM 708337 Disassembling and assembling front roof console

Disassembling front roof console





Remove front roof console. -> 601219 Removing and installing switch for sunroof - section on "Removing" Service and Repair

Information

- The repair description relates to a fully equipped roof console.

1. Unscrew fastening screw -1- and take out the sun visor along with the support -2- ( -arrow- ).





2. Unlock connector on garage door opener control unit -arrows A- and pull it off -arrow B-.





3. Unscrew the two fastening screws -2- and remove the control unit -arrow C-.





4. Unscrew the fastening screws -3- and take out the support -arrow D-.





Information

- Only if replacing the printed circuit board





5. Turn the sockets of the bulbs for interior lighting to the left -arrow A- and remove them -arrow B-.





6. Pull the piece of plastic foam off the plug connection -arrow A-.





7. Disconnect plug connection -arrows B-.





8. Carefully pull the three locking tabs -A- apart and pull the switch up and out -B-.





9. Release sensor for interior monitoring -arrows A- and remove it from the roof console -arrows B-.





10. Unscrew the four fastening screws -4- and remove printed circuit board for interior lighting -arrow-.





11. Carefully pull the connector off the printed circuit board -arrow B-.





12. Press in the two clips -arrows A- and press the reading light out in a downward direction -arrow B-.





13. Release the microphone holder using a small screwdriver -arrows A- and remove the microphone -arrow B-.





14. Unscrew the three fastening screws -5-.





15. Turn the printed circuit board -arrow A- and pull the connector off the printed circuit board (P- & SOS button) -arrow B-.





16. Unscrew the four fastening screws -6-.





17. Turn the printed circuit board (garage door opener) -arrow A- and pull the two connectors off the printed circuit board -arrows B-.





18. Unscrew the three fastening screws -7-.





19. Remove the printed circuit board (sun blind) -arrow A- and pull off the connector -arrow B-.





20. Remove the wiring harness from the brackets -arrows-.





21. Release the cover -arrows A- and unfold it downwards -arrow B-.





22. Release the lighting unit -arrow C- and press it down and out -arrow D-.





23. Release the nine locking tabs -arrows A- and press the two covers down and out -arrows B-.





24. Release the nine locking tabs -arrows A- and carefully press the cover down and out -arrow B-.





25. Press the clip together -arrows A- and carefully remove the spring -arrow B-.





26. Remove the contact bridge -1- ( -arrow C- ).





27. Carefully pull the holder out of the locking mechanism -2- ( -arrows D- ) and pull the switch -3- down and out -arrow E-.





28. Carefully press switch trim for sun blind to the inside -arrow A- and remove it -arrow B-.





29. Release the switch trims -arrows A- and remove them -arrows B-.





30. Unscrew both fastening screws -8-.





31. Move spring -1- for the push-button -2- to the left -arrow A- and remove it -arrow B-.





32. Remove push-button -arrow C-.





33. Release closing damper -arrows A- and remove it -arrow B-.





34. Press the right bearing pin at the edge inwards -arrow A- -arrow A- , pivot the shelf down -arrow B- and remove it -arrow C-. Push the spring through the opening at the same time -arrow D-.





35. Pull off the bearing sleeve -arrow A- and remove the spring -arrow B-.






Assembling front roof console





Information

- The springs for the shelf are assigned to the right and left side. Given this, please make sure to observe the installation position of the springs.

1. Place the springs on the pivot axis -1- and the retaining pivot -2- ( -arrows- ).





2. Connect the bearing sleeve with the contact surface -3- pointing towards the spring at the pivot axis. Make sure that the flat edge -4- of the contact surface is facing downwards.





3. Insert the fully opened shelf at the left side -arrow A-. Push the spring through the opening -arrow B-.





4. Insert the spring at the right side through the opening -arrow C-.





5. Press in the bearing pin at the underside -arrow D- , then press the shelf into the roof console -arrow E- until the bearing pin with the bearing sleeve engages securely.





6. Press in the closing damper -arrow A- until you feel the locking tabs -B- engage.





7. Place the push-button -1- in installation position -arrow A-.





8. Insert the spring -2- ( -arrow B- ), move it to the right -arrow C- , and screw down using the two fastening screws -8-.