973219 Removing and installing wire harness for door
WM 973219 Removing and installing wire harness for door
Information
Component information - front door
Installation position of wire harness for front door
Information
Component information - rear door
Installation position of wire harness for rear door
Preliminary work
Preliminary work for front door panel
1. Remove front door panel. -> 705919 Removing and installing front door panel - section on "Removing" 705919 Removing and installing front door panel
Preliminary work for rear door panel
1. Remove rear door panel. -> 707319 Removing and installing rear door panel - section on "Removing" 707319 Removing and installing rear door panel
Preliminary work for front door sub-frame
Remove front door sub-frame. -> 573019 Removing and installing front door sub-frame - section on "Removing" 573019 Removing and Installing Front Door Unit Carrier
Preliminary work for rear door sub-frame
1. Remove rear door sub-frame. -> 583019 Removing and installing rear door sub-frame - section on "Removing" 583019 Removing and Installing Rear Door Sub-frame
Removing wire harness for door
Removing wire harness for door in front door panel
NOTICE
Voltage peaks
- Risk of damage to electrical load or to the control unit
-> Remove remote control and switch off ignition before disconnecting or removing electrical load.
Information
Some of the repair illustrations show only one side of the vehicle. Naturally, some steps also have to be performed on the opposite side of the vehicle as well. These must be carried out as a mirror image of the steps shown.
Information
The number of plug connections can vary, depending on equipment.
1. Carefully remove insulating mat.
2. Disconnect electric plug connections.
2.1. Pull off electric plug connection for alarm system LED.
Pulling off connector for alarm system LED
2.2. Pull off electric plug connection for light for door opener.
Pulling off connector for light for door opener
2.3. Pull off electric plug connection for switch for memory seat adjustment.
Pulling off connector for memory seat adjustment
2.4. Release electric plug connection for power windows switch -a- and pull it off -A-.
Pulling off connector for power windows switch
2.5. Release and pull off electric plug connection for the storage compartment light -1-.
Pulling off connector for storage compartment light
2.6. Only on vehicles with electric sunblind:
Pull off electric plug connection for sunblind switch -2-.
2.7. Pull off electric plug connection for door warning light.
Pulling off connector for door warning light
3. Unclip fixing clips for wire harness.
Unclipping fixing clips
Removing wire harness for door in rear door panel
NOTICE
Voltage peaks
- Risk of damage to electrical load or to the control unit
-> Remove remote control and switch off ignition before disconnecting or removing electrical load.
Information
Some of the repair illustrations show only one side of the vehicle. Naturally, some steps also have to be performed on the opposite side of the vehicle as well. These must be carried out as a mirror image of the steps shown.
Information
The number of plug connections can vary, depending on equipment.
1. Carefully remove insulating mat.
2. Disconnect electric plug connections.
2.1. Release and pull off electric plug connection for light for door opener.
Pulling off connector for light for door opener
2.2. Pull off electric plug connection for ashtray light.
Pulling off connector for ashtray light
2.3. Pull off electric plug connection for power windows switch.
Pulling off connector for power windows switch
2.4. Release and pull off electric plug connection for the storage compartment light -1-.
Pulling off connector for storage compartment light
2.5. Only on vehicles with electric sunblind:
Pull off electric plug connection for sunblind switch -2-.
2.6. Pull off electric plug connection for door warning light.
Pulling off connector for door warning light
3. Unclip fixing clips for wire harness.
Unclipping fixing clips
Removing wire harness for door in front door sub-frame
NOTICE
Voltage peaks
- Risk of damage to electrical load or to the control unit
-> Remove remote control and switch off ignition before disconnecting or removing electrical load.
Information
Some of the repair illustrations show only one side of the vehicle. Naturally, some steps also have to be performed on the opposite side of the vehicle as well. These must be carried out as a mirror image of the steps shown.
Information
The number of plug connections can vary, depending on equipment.
1. Disconnect electric plug connections.
1.1. Release and pull off electric plug connections -1+2- on the door control unit.
Pulling off connectors on door control unit
1.2. Release and pull off electric plug connection for power windows motor.
Pulling off connector for power windows motor
1.3. Release and pull off electric plug connection for pressure sensor.
Pulling off connector for pressure sensor
1.4. Release and pull off electric plug connection for woofer.
Pulling off connector for woofer
2. Unclip fixing clips for wire harness at the inside.
Unclipping inner fixing clips
3. Unclip fixing clips for wire harness at the outside and press the rubber sleeves -3- out of the opening in the door sub-frame.
Unclipping outer fixing clips
4. Guide wire harness out of the door sub-frame.
Removing wire harness for door in rear door sub-frame
NOTICE
Voltage peaks
- Risk of damage to electrical load or to the control unit
-> Remove remote control and switch off ignition before disconnecting or removing electrical load.
Information
Some of the repair illustrations show only one side of the vehicle. Naturally, some steps also have to be performed on the opposite side of the vehicle as well. These must be carried out as a mirror image of the steps shown.
Information
The number of plug connections can vary, depending on equipment.
1. Disconnect electric plug connections.
1.1. Release and pull off electric plug connections -1+2- for the door wire harness at the door control unit.
Pulling off connectors for door control unit
1.2. Release and pull off electric plug connection for power windows motor.
Pulling off connector for power windows motor
1.3. Release and pull off electric plug connection for woofer.
Pulling off connector for woofer
2. Unclip fixing clips for wire harness at the inside.
Unclipping inner fixing clips
3. Unclip fixing clips for wire harness at the outside -A- and press the rubber sleeves -3- out of the opening in the door sub-frame -B-.
Removing rubber sleeves
4. Guide wire harness out of the door sub-frame.
Installing wire harness for door
Installing wire harness for door in front door sub-frame
Information
Some of the repair illustrations show only one side of the vehicle. Naturally, some steps also have to be performed on the opposite side of the vehicle as well. These must be carried out as a mirror image of the steps shown.
Information
The number of plug connections can vary, depending on equipment.
1. Guide wire harness into the door sub-frame.
2. Clip in fixing clips for wire harness for door sub-frame at the outside and press the rubber sleeves -3- into the opening in the door sub-frame. Check that they are seated correctly.
Securing wire harness at the outside
3. Clip in fixing clips for wire harness for door sub-frame at the inside.
Securing wire harness at the inside
4. Connect electric plug connections.
4.1. Plug in electric plug connection for pressure sensor until it engages securely.
Plugging in connector for pressure sensor
4.2. Plug in electric plug connection for power windows motor until it engages securely.
Plugging in connector for power windows motor
4.3. Plug in electric plug connection for woofer until it engages securely.
Plugging in connector for woofer
4.4. Plug in and lock electric plug connections -1+2- at the door control unit.
Plugging in connectors for door control unit
Installing wire harness for door in rear door sub-frame
Information
Some of the repair illustrations show only one side of the vehicle. Naturally, some steps also have to be performed on the opposite side of the vehicle as well. These must be carried out as a mirror image of the steps shown.
Information
The number of plug connections can vary, depending on equipment.
1. Guide wire harness into the door sub-frame.
2. Clip in wire harness at the door sub-frame.
Clipping in wire harness
3. Secure wire harness with a new tie-wrap -A-. Press rubber sleeves -3- into the opening in the door sub-frame -B-. Check that they are seated correctly.
Securing rubber sleeves
4. Connect electric plug connections.
4.1. Plug in electric plug connection for woofer until it engages securely.
Plugging in connector for woofer
4.2. Plug in electric plug connection for power windows motor until it engages securely.
Plugging in connector for power windows motor
4.3. Plug in and lock electric plug connections -1+2- at the door control unit.
Plugging in connectors for door control unit
Installing wire harness for door in front door panel
Information
Some of the repair illustrations show only one side of the vehicle. Naturally, some steps also have to be performed on the opposite side of the vehicle as well. These must be carried out as a mirror image of the steps shown.
Information
The number of plug connections can vary, depending on equipment.
1. Secure fixing clips.
Securing fixing clips
2. Connect electric plug connections.
2.1. Plug in electric plug connection for storage compartment -1- until it engages securely.
Plugging in connector for storage compartment light
2.2. Only on vehicles with electric sunblind:
Plug in electric plug connection for sunblind switch -2-.
2.3. Plug in electric plug connection for power windows switch until it engages securely.
Plugging in connector for power windows switch
2.4. Plug in electric plug connection for memory seat adjustment.
Plugging in connector for memory seat adjustment
2.5. Plug in electric plug connection for door warning light until it engages securely.
Plugging in connector for door warning light
2.6. Plug in electric plug connection for light for door opener until it engages securely.
Plugging in connector for light for door opener
2.7. Plug in electric plug connection for alarm system LED.
Plugging in connector for alarm system LED
3. Fit insulating mat.
Installing wire harness for door in rear door panel
Information
Some of the repair illustrations show only one side of the vehicle. Naturally, some steps also have to be performed on the opposite side of the vehicle as well. These must be carried out as a mirror image of the steps shown.
Information
The number of plug connections can vary, depending on equipment.
1. Secure fixing clips.
Securing fixing clips
2. Connect electric plug connections.
2.1. Plug in electric plug connection for door warning light until it engages securely.
Plugging in connector for door warning light
2.2. Plug in electric plug connection for power windows switch.
Plugging in connector for power windows switch
2.3. Plug in electric plug connection for ashtray light until it engages securely.
Plugging in connector for ashtray light
2.4. Plug in electric plug connection for the storage compartment light -1-.
Plugging in connector for storage compartment light
2.5. Only on vehicles with electric sunblind:
Plug in electric plug connection for sunblind switch -2-.
2.6. Plug in electric plug connection for light for door opener until it engages securely.
Plugging in connector for light for door opener
3. Insert insulating mat.
Subsequent work
Subsequent work for front door sub-frame
1. Install front door sub-frame. -> 573019 Removing and installing front door sub-frame - section on "Installing" 573019 Removing and Installing Front Door Unit Carrier
Subsequent work for rear door sub-frame
1. Install rear door sub-frame. -> 583019 Removing and installing rear door sub-frame - section on "Installing" 583019 Removing and Installing Rear Door Sub-frame
Subsequent work for front door panel
1. Install front door panel. -> 705919 Removing and installing front door panel - section on "Installing" 705919 Removing and installing front door panel
Subsequent work for rear door panel
1. Install rear door panel. -> 707319 Removing and installing rear door panel - section on "Installing" 707319 Removing and installing rear door panel