Brake Warning Indicator Malfunction
Brake Warning Indicator Malfunction
Diagnostic Instructions
* Perform the Diagnostic System Check - Vehicle (Diagnostic System Check - Vehicle) prior to using this diagnostic procedure.
* Review Strategy Based Diagnosis (Strategy Based Diagnosis) for an overview of the diagnostic approach.
* Diagnostic Procedure Instructions (Diagnostic Procedure Instructions) provides an overview of each diagnostic category.
Diagnostic Fault Information
Circuit/System Description
The brake fluid level switch monitors the level of brake fluid in the master cylinder. When the electronic brake control module (EBCM) sees the brake fluid level switch input grounded, it sends a serial data message to the instrument panel cluster (IPC) to turn ON the Red Brake Warning indicator. The body control module (BCM) sees the park brake switch input grounded, it sends a serial data message to the IPC requesting illumination of the Red Brake Warning indicator.
Reference Information
Schematic Reference
Hydraulic Brake Schematics ([1][2]Electrical Diagrams)
Connector End View Reference
Component Connector End Views (Component Connector End Views)
Description and Operation
Brake Warning System Description and Operation (Brake Warning System Description and Operation)
Electrical Information Reference
* Circuit Testing (Circuit Testing)
* Connector Repairs (Connector Repairs)
* Testing for Intermittent Conditions and Poor Connections (Testing for Intermittent Conditions and Poor Connections)
* Wiring Repairs (Wiring Repairs)
Scan Tool Reference
Control Module References (Control Module References) for scan tool information
Circuit/System Verification
1. Verify the park brake is released and the brake fluid is at or above the proper level.
• If low, refer to Brake Fluid Loss (Brake Fluid Loss).
2. Command the IPC lamp test with a scan tool, the warning indicator should turn ON.
• If the red brake warning indicator does not illuminate, replace the IPC.
3. Ignition ON, observe the scan tool BCM Park Brake Switch parameter while applying and releasing the park brake. The parameter should cycle between Set and Released.
• If the parameter does not cycle between the specified values, refer to Park Brake Switch Malfunction.
4. Observe the scan tool EBCM Brake Fluid Level Switch parameter. The reading should be OK.
• If not the specified value, refer to Brake Fluid Level Switch Malfunction.
Circuit/System Testing
Park Brake Switch Malfunction
1. Ignition OFF, disconnect the harness connector at the park brake switch.
2. Ignition ON, verify the scan tool BCM Park Brake Switch parameter is Released.
• If not the specified value, test the signal circuit terminal A for a short to ground. If the circuit tests normal, replace the BCM.
3. Install a 3A fused jumper wire between the signal circuit terminal A and ground. Verify the scan tool BCM Park Brake Switch parameter is Set.
• If not the specified value, test the signal circuit for a short to voltage or an open/high resistance.
4. If all circuits test normal, test or replace the park brake switch.
Brake Fluid Level Switch Malfunction
1. Ignition OFF, disconnect the harness connector at the brake fluid level switch.
2. Test for less than 1 ohm between the ground circuit terminal A and ground.
• If greater than the specified range, test the ground circuit for an open/high resistance.
3. Ignition ON, verify the scan tool EBCM Brake Fluid Level Switch parameter is OK.
• If not the specified value, test the signal circuit for a short to ground. If the circuit tests normal, replace the EBCM.
4. Install a 3A fused jumper wire between the signal circuit terminal B and ground. Verify the scan tool EBCM Brake Fluid Level Switch parameter is Low.
• If not the specified value, test the signal circuit for a short to voltage or an open/high resistance. If the circuit tests normal, replace the EBCM.
5. If all circuits test normal, test or replace the brake fluid level switch.
Component Testing
Park Brake Switch Malfunction
1. Ignition OFF, disconnect the harness connector at the park brake switch.
2. Test for infinite resistance between the signal terminal A and ground with the park brake released.
• If less than the specified value, replace the park brake switch.
3. Test for less than 1 ohm between the signal terminal A and ground with the park brake applied.
• If greater than the specified range, replace the park brake switch.
Brake Fluid Level Switch Malfunction
1. Ignition OFF, disconnect the harness connector at the brake fluid level switch.
2. Test for infinite resistance between the ground terminal A and the signal terminal B.
• If less than the specified value, replace the brake fluid level switch.
Repair Instructions
Perform the Diagnostic Repair Verification (Verification Tests) after completing the diagnostic procedure.
* Brake Fluid Level Indicator Switch Replacement (Service and Repair)
* Parking Brake Indicator Switch Replacement (Service and Repair)
* Control Module References (Control Module References) for EBCM and IPC replacement, setup, and programming