Installation
AIR CONDITIONING: BLOWER UNIT: INSTALLATION
1. INSTALL BLOWER ASSEMBLY
(a) Install the blower unit with the 3 screws as shown in the illustration.
2. INSTALL NO. 2 AIR DUCT SUB-ASSEMBLY Installation
3. TEMPORARILY TIGHTEN AIR CONDITIONING UNIT Installation
4. INSTALL INSTRUMENT PANEL REINFORCEMENT ASSEMBLY (for Manual Transaxle) Installation
5. INSTALL INSTRUMENT PANEL REINFORCEMENT ASSEMBLY (for Automatic Transaxle) Installation
6. INSTALL AIR CONDITIONING UNIT Installation
7. INSTALL INSTRUMENT PANEL WIRE Installation
8. CONNECT DRAIN COOLER HOSE Installation
9. INSTALL POWER STEERING ECU ASSEMBLY Installation
10. INSTALL REAR NO. 2 AIR DUCT Installation
11. INSTALL INSTRUMENT PANEL BRACE SUB-ASSEMBLY Installation
12. INSTALL RELAY BLOCK ASSEMBLY Installation
13. INSTALL NO. 1 AIR DUCT SUB-ASSEMBLY Installation
14. INSTALL CENTER INSTRUMENT PANEL TO COWL BRACE Installation
15. INSTALL LOWER DEFROSTER NOZZLE ASSEMBLY Installation
16. INSTALL REAR NO. 1 AIR DUCT Installation
17. INSTALL REAR NO. 3 AIR DUCT Installation
18. INSTALL STEERING COLUMN ASSEMBLY Installation
19. TURN FRONT WHEELS FACING STRAIGHT AHEAD
20. CONNECT NO. 2 STEERING INTERMEDIATE SHAFT ASSEMBLY Installation
21. INSTALL COLUMN HOLE COVER SILENCER SHEET Installation
22. TURN FRONT WHEELS FACING STRAIGHT AHEAD
23. INSTALL TURN SIGNAL SWITCH ASSEMBLY WITH SPIRAL CABLE SUB-ASSEMBLY Installation
24. INSTALL STEERING COLUMN COVER Installation
25. ADJUST SPIRAL CABLE Installation
26. INSTALL STEERING WHEEL ASSEMBLY Installation
27. INSTALL STEERING PAD Installation
28. INSTALL LOWER INSTRUMENT PANEL SUB-ASSEMBLY Installation
29. INSTALL ANTENNA CORD SUB-ASSEMBLY Installation
30. INSTALL HOOD LOCK CONTROL LEVER SUB-ASSEMBLY Installation
31. INSTALL NO. 1 INSTRUMENT CLUSTER FINISH PANEL SEAL Installation
32. INSTALL RADIO BRACKET Installation
33. INSTALL INSTRUMENT PANEL SUB REINFORCEMENT Installation
34. INSTALL INSTRUMENT PANEL FINISH LOWER PANEL SUB-ASSEMBLY Installation
35. INSTALL NO. 1 SWITCH HOLE BASE Installation
36. CONNECT AIR MIX DAMPER CONTROL CABLE SUB-ASSEMBLY Installation
37. CONNECT NO. 2 HEATER CONTROL CABLE SUB-ASSEMBLY Installation
38. INSTALL AIR CONDITIONING PANEL ASSEMBLY Installation
39. INSTALL SHIFT LEVER ASSEMBLY (for Automatic Transaxle) Installation
40. CONNECT TRANSMISSION CONTROL CABLE ASSEMBLY (for Automatic Transaxle) Installation
41. INSPECT SHIFT LEVER POSITION (for Automatic Transaxle) On-Vehicle Inspection
42. ADJUST SHIFT LEVER POSITION (for Automatic Transaxle) Installation
43. INSTALL SHIFT LEVER ASSEMBLY (for Manual Transaxle) Installation
44. CONNECT TRANSMISSION CONTROL CABLE ASSEMBLY (for Manual Transaxle) Installation
45. ADJUST TRANSMISSION CONTROL CABLE ASSEMBLY (for Manual Transaxle) Adjustments
46. INSTALL INSTRUMENT PANEL FINISH LOWER PANEL Installation
47. INSTALL FRONT NO. 1 CONSOLE BOX INSERT Installation
48. INSTALL FRONT NO. 2 CONSOLE BOX INSERT Installation
49. INSTALL INSTRUMENT CLUSTER FINISH CENTER LOWER PANEL Installation
50. INSTALL SHIFT LEVER KNOB SUB-ASSEMBLY (for Manual Transaxle) Installation
51. INSTALL COWL SIDE TRIM BOARD RH Installation
52. INSTALL COWL SIDE TRIM BOARD LH Installation
53. INSTALL FRONT DOOR SCUFF PLATE RH Installation
54. INSTALL FRONT DOOR SCUFF PLATE LH Installation
55. INSTALL UPPER INSTRUMENT PANEL SUB-ASSEMBLY Installation
56. INSTALL GLOVE COMPARTMENT DOOR ASSEMBLY Installation
57. INSTALL COMBINATION METER ASSEMBLY Installation
58. INSTALL INSTRUMENT CLUSTER FINISH PANEL ASSEMBLY Installation
59. INSTALL INSTRUMENT CLUSTER FINISH LOWER PANEL Installation
60. INSTALL INSTRUMENT CLUSTER FINISH CENTER PANEL SUB-ASSEMBLY Installation
61. INSTALL FRONT PILLAR GARNISH RH Installation
62. INSTALL FRONT PILLAR GARNISH LH Installation
63. INSTALL FRONT DOOR OPENING TRIM WEATHERSTRIP RH Installation
64. INSTALL FRONT DOOR OPENING TRIM WEATHERSTRIP LH Installation
65. INSPECT STEERING PAD Installation
66. INSPECT STEERING WHEEL CENTER POINT
67. CONNECT HEATER OUTLET WATER HOSE Installation
68. CONNECT HEATER INLET WATER HOSE Installation
69. INSTALL AIR CONDITIONING TUBE AND ACCESSORY ASSEMBLY Installation
70. INSTALL SUCTION PIPE SUB-ASSEMBLY Installation
71. CHARGE WITH REFRIGERANT Service and Repair
72. ADD ENGINE COOLANT Service and Repair
73. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL
Torque : 5.4 Nm (55 kgf-cm, 48 in-lbf)
74. INSPECT FOR COOLANT LEAK Testing and Inspection
75. INITIALIZE ROTATION ANGLE SENSOR AND CALIBRATE TORQUE SENSOR ZERO POINT
Programming and Relearning
76. INSPECT SRS WARNING LIGHT
Diagnosis System
77. WARM UP ENGINE Service and Repair
78. INSPECT FOR REFRIGERANT LEAK Service and Repair