With VDC
WIRING DIAGRAMWIRING DIAGRAM:
Subaru Select Monitor
OPERATION
READ DIAGNOSTIC TROUBLE CODE (DTC)
1) Prepare the Subaru Select Monitor kit.
2) Connect the diagnosis cable to the Subaru Select Monitor.
3) Connect the Subaru Select Monitor to the data link connector.
(1) Data link connector is located in the lower portion of instrument panel (on the driver's side).
(1) Data link connector:
(2) Connect the diagnosis cable to the data link connector.
CAUTION: Do not connect scan tools other than the Subaru Select Monitor.
4) Turn the ignition switch to ON (engine OFF) and run the Subaru Select Monitor.
5) On the �Main Menu� display screen, select the {Each System Check}.
6) On the �System Selection Menu� display screen, select the {Brake Control}.
7) Select the [OK] after the {VDC} is displayed.
8) On the �VDC Diagnosis� screen, select the {Diagnostic Code(s) Display}.
NOTE:
^ For details concerning operation procedures, refer to the "SUBARU SELECT MONITOR OPERATION MANUAL".
^ For details concerning DTCs, refer to Diagnostic Trouble Code Descriptions.
^ Up to 3 DTCs are displayed in the order of detection.
^ If a particular DTC is not stored in memory properly at the occurrence of problem (due to a drop in VDCCM&H/U power supply etc.), the DTC suffixed with a question mark " - " is displayed on Subaru Select Monitor display screen. This shows it may be an unreliable reading.
9) If VDC and Subaru Select Monitor cannot communicate, check the communication circuit.
READ CURRENT DATA
1) On the �Main Menu� display screen, select the {Each System Check}.
2) On the �System Selection Menu� display screen, select the {Brake Control}.
3) Select the [OK] after {VDC} is displayed.
4) On the �Brake Control Diagnosis� display screen, select the {Current Data Display/Save}.
5) On the �Display Menu� screen, select the data display method.
6) Using the scroll key, scroll the display screen up or down until necessary data is shown.
^ A list of the support data is shown in this table.
NOTE: For details concerning operation procedures, refer to the "SUBARU SELECT MONITOR OPERATION MANUAL".
CLEAR MEMORY MODE
1) On the �Main Menu� display screen, select the {2. Each System Check}.
2) On the �System Selection Menu� display screen, select the {Brake Control}.
3) Select the [OK] after {VDC} is displayed.
4) On the �Brake Control Diagnosis� display screen, select the {Clear Memory}.
5) When "Done" and "Turn ignition switch to OFF" are shown on the display screen, turn the ignition switch to OFF and close the Subaru Select Monitor.
NOTE: For details concerning operation procedures, refer to the "SUBARU SELECT MONITOR OPERATION MANUAL".
ABS SEQUENCE CONTROL
FREEZE FRAME DATA
NOTE:
^ Data stored at the time of trouble occurrence is shown on the display.
^ Each time a trouble occurs, the latest information is stored in the freeze frame data in memory.
^ If a freeze frame data is not properly stored in memory (due to a drop in VDCCM power supply, etc.), a DTC suffixed with a question mark " - " appears on the Subaru Select Monitor display. This shows it may be an unreliable reading.
PARAMETER SELECTION
CAUTION:
^ For parameter selection, the Subaru Select Monitor III is required.
^ This function can be used for the replacement VDCCM&H/U and VDCCM.
NOTE:
^ When a VDCCM is replaced with a replacement, use this function to select and register parameters to the VDCCM.
^ For confirmation of applied models, refer to the "Model number plate" attached to the vehicles.
^ If a wrong applied model is written, it can be rewritten.
^ When no data is registered, ABS/EBD/VDC warning light illuminates and the DTC "Parameter selection failure" is detected.
1) Connect the Subaru Select Monitor III.
2) On the �Main Menu� display screen, select the {Each System Check}.
3) On the �System Selection Menu� display screen, select the {Brake Control}.
4) Select the [OK] after {VDC} is displayed.
5) On the "Brake Control Diagnosis" display screen, select the {Parameter Selection}.
6) Check the applied model indicated in the "Model number plate".
7) Enter the applied model of 7-digit alphanumeric characters and select the [Enter].
8) When the confirmation screen indicating the vehicle information appears, check that the correct applied model and grade are displayed and select the "OK".
NOTE: When the displayed applied model and grade are different from those of the vehicle, perform registration operations again after selecting the "OK".
9) Execute Clear Memory after parameter selection and registration operations because the DTC for "Parameter selection failure" is memorized.
PARAMETER CHECK
NOTE: The parameter data registered in the VDCCM is shown on the display.
1) Connect the Subaru Select Monitor III.
2) On the �Main Menu� display screen, select the {Each System Check}.
3) On the �System Selection Menu� display screen, select the {Brake Control}.
4) Select the [OK] after {VDC} is displayed.
5) On the"Brake Control Diagnosis" display screen, select {Parameter Check}.
6) On the {Parameter Check} display screen, check that the applied model and grade of the target vehicle are included and select the [OK].
7) If the applied model and grade of the target vehicle are not included on the {Parameter Check} display screen, perform parameter selection and registration.