Operation CHARM: Car repair manuals for everyone.
Home >> Subaru >> 2009 >> Legacy F6-3.0L DOHC >> Repair and Diagnosis >> Body and Frame >> Body Control Systems >> Testing and Inspection >> Scan Tool Testing and Procedures >> Subaru Select Monitor

Subaru Select Monitor

Subaru Select Monitor

OPERATION

1. READ DIAGNOSTIC TROUBLE CODE (DTC)

NOTE:
- DTC is displayed in the sequence of inputting. (When entering two DTCs or more simultaneously, they are displayed in the sequence of priority.)
- When more than one DTC is displayed, perform the diagnosis of top one.

1. Prepare the Subaru Select Monitor kit.
2. Connect the diagnosis cable to Subaru Select Monitor.
3. Connect the Subaru Select Monitor to data link connector.
Data link connector is located in the lower portion of instrument panel (on the driver's side).






CAUTION: Do not connect scan tools other than the Subaru Select Monitor.

4. Turn the ignition switch to ON (engine OFF) and run the Subaru Select Monitor.
5. On the <
> display, select the {Each System Check}.
6. On the <> display, select the {Integ. unit mode}.
7. On the <> display, select the {Diagnostic Code(s) Display}.

NOTE:
- For details concerning the operation procedure, refer to the "PC application help for Subaru Select Monitor".
- For details concerning DTCs, refer to the List of Diagnostic Trouble Code (DTC). DTC List - B and U Codes

2. READ CURRENT DATA
1. On the <
> display screen, select the {Each System Check}.
2. On the <> display screen, select the {Integ. Unit mode}.
3. On the <> display screen, select the {Current Data Display & Save}.
4. On the <> display screen, select the {Data Display}.
5. Using the scroll key, scroll the display screen up or down until the desired data is shown.
A support list contains both of analog and digital data, and they are shown in the following table.

3. DISPLAY OF ANALOG DATA






4. DISPLAY OF ON/OFF DATA

Part 1:




Part 2:




Part 3:






NOTE: For details concerning the operation procedure, refer to the "PC application help for Subaru Select Monitor".

5. CONFIRMATION OF CURRENT SETTING
1. On the <
> display, select the {Each System Check}.
2. On the <> display, select the {Integ. unit mode}.
3. On the <> display, select the {Current Data Display & Save}.
4. On the <> display, select the {Data Display}.
5. Using the scroll key, scroll the display screen up or down until the desired data is shown.
6. Display the following item and record the settings.
Required items for new registration (Except for system not equipped)






6. REGISTRATION BODY INTEGRATED UNIT (EQUIPMENT SETTING)

CAUTION:
Body integrated unit is core of LAN system, and also can select the function of all vehicle system control. To perform normal operation of vehicle and diagnosis, the above settings must match the actual vehicle equipment.
If registrations and function setting are different from vehicle equipment, vehicle system does not operate normally and diagnosis cannot be performed correctly. Pay attention to following item.
- Be sure to correspond registrations and function settings to vehicle equipment.
- Do not change the settings of vehicle improperly.
- Confirm key illumination does not blink or "Factory or Market setting" of body integrated unit registrations is "Market". If "Factory or Market setting" is set to "Factory," key illumination blinks when ignition key is turned ON, to notify that the settings are unconfirmed.
- Key illumination does not blink with ignition switch turned to ON and go off with door closed.
- Be sure to register immobilizer if body integrated unit is replaced with a new part, (models with immobilizer)
- Make a registration of immobilizer when the parts related to immobilizer have been replaced. For details, refer to the "PC application help for Subaru Select Monitor".

1. Turn the ignition switch to OFF.
2. Connect the Subaru Select Monitor to data link connector.






3. Turn the ignition switch to ON and run the Subaru Select Monitor.
4. On the <
> display, select the {Each System Check}.
5. On the <> display, select the {Integ. unit mode} and then select the <>
6. Change the setting with UP/DOWN key and select the [OK].
List of body integrated unit registration item

NOTE: Setting is different depending on the grade of vehicle.






CAUTION:
- To perform normal operation of vehicle and diagnosis, the above settings must match the actual vehicle equipment.
- When body integrated unit is a new part or "Factory" mode, key illumination blinks to show equipment settings have not been completed.
- Be sure not to change Factory or Market setting except when installing a new body integrated unit.

NOTE:
"Factory" mode:
- Body integrated unit has not been set yet. It can be recognized by key illumination blinking with ignition switch turned to ON.
- All replacement body integrated units are set to "Factory" mode. When replacing a body integrated unit, be sure to perform the registration operation.
"Market" mode:
Each settings have been set. It can be recognized by key illumination coming on in concocting with room light and going off with ignition switch turned to ON.

7. Perform the Factory setting. On the <> display screen of Subaru Select Monitor, select the {Factory or Market setting} and select the [OK].
8. Change the mode from Factory to Market.
9. Change to the immobilizer cartridge, and register the immobilizer key. (For models with immobilizer, perform the operation according to the "PC application help for Subaru Select Monitor".)
10. When key registration is completed, "Do you want to register remote engine start?" is displayed. Perform registration only for equipped models.
11. Perform the function setting (ECM customizing).

NOTE: For details concerning the operation procedure, refer to the "PC application help for Subaru Select Monitor".

7. CLEAR MEMORY MODE
1. On the <
> display, select the {2. Each System Check}.
2. On the <> display, select the {Integ. unit mode}.
3. Select the [OK] after the information of body integrated unit type is displayed.
4. On the <> display, select the {Clearing Memory}.






5. When "Done" is shown on the display screen, turn the ignition switch to OFF.

NOTE: For details concerning the operation procedure, refer to the "PC application help for Subaru Select Monitor".

8. FREEZE FRAME DATA

NOTE:
- Data stored at the time of trouble occurrence is shown on the display.
- Freeze frame data will be memorized maximum to 20.
- If freeze frame data is not stored in memory correctly (caused by low power supply of body integrated unit), DTC will be displayed with "?" on the head of it in the Subaru Select Monitor display. This shows it may be an unreliable reading.


9. FUNCTION SETTING (ECM CUSTOMIZING)
1. On the <
> display, select the {Each System Check}.
2. On the <> display, select the {Integ. unit mode}.
3. On the <> display, select the {ECM customizing}.
4. Change the setting with UP/DOWN key and set with the [OK].
List of function setting item (ECM customizing)

Part 1:




Part 2:






5. After setting, make sure that vehicle equipment is same as the setting changed in the {Current Data Display & Save}.

CAUTION:
- The above settings must match the actual vehicle equipment for proper operation.
- Do not change settings except for setting above while setting the functions.
- Be sure not to change Factory or Market setting except when installing a new body integrated unit.

NOTE: For details concerning the operation procedure, refer to the "PC application help for Subaru Select Monitor".

10. FUNCTION CHECK
In order to check the body integrated unit function, inspect the body integrated unit and actuator using Subaru Select Monitor without operating switches.
1. On the <
> display, select the {Each System Check}.
2. On the <> display, select the {Integ. unit mode}.
3. On the <> display, select the {Function check}.
4. Select the item to be operated on the <> display screen with "UP/Down key" and select the [OK].






5. Pressing [OK] starts, [NO] cancels the operation and [OK] returns to the System Operation Check Mode display screen.

NOTE: If not equipped (based on area or condition), process will not go on.

INSPECTION

1. COMMUNICATION FOR INITIALIZING IMPOSSIBLE

DETECTING CONDITION:
Faulty harness connectors

TROUBLE SYMPTOM:
Not communicable with Subaru Select Monitor.

WIRING DIAGRAM

Wiring Diagram:






Step 1-10:




Step 11-12:






CAUTION: When replacing body integrated unit on the model with immobilizer system, refer to the "PC application help for Subaru Select Monitor"

2. WITHOUT DTC

DETECTING CONDITION:
Defective combination meter

TROUBLE SYMPTOM:
- Communication error display in odo/trip meter is not cleared. (Except for meter with MID)
- "No diagnostic Code Present" will be displayed on the Subaru Select Monitor, is displayed on Subaru Select Monitor.

NOTE: If DTC is not displayed on Subaru Select Monitor, LAN communication System should be OK.

Step 1-4:




pro multis · About Operation CHARM