Valve and Cylinder Head Disassembly and Reassembly
Valve and Cylinder Head Disassembly and ReassemblyDisassembly
Reference: Valve and Cylinder Head Removal and Installation
NOTE:
If following parts are removed, keep them in order. They must go back in the position from which they were removed.
^ Valve cotter
^ Valve spring retainer
^ Valve spring
^ Valve spring seat
^ Intake valve
^ Exhaust valve
^ Tappet
1) Remove oil venturi plug (1).
2) Remove tappets from cylinder head.
3) Using special tools (A) and (B), compress valve spring and then remove valve cotters (1) also by using special tool (C).
CAUTION:
When compressing the valve spring, be careful not to damage in inside surface of tappet installing hole.
Special Tool
(A): 09916-14510
(B): 09916-14522
(C): 09916-84511
4) Release special tools (A) and (B), and remove spring retainer and valve spring.
5) Remove valve from combustion chamber side.
6) Remove valve stem seal (1) and valve spring seat (2).
7) Using special tool, drive out valve guide from combustion chamber side to valve spring side.
NOTE:
Heat cylinder head to remove valve guide, if necessary.
Special Tool
(A): 09916-44910
Reassembly
Reference: Valve and Valve Guide Inspection
Reference: Cylinder Head Inspection
Reference: Valve Spring Inspection
1) Before installing valve guide into cylinder head, ream guide hole with special tool (10.5 mm reamer) so as to remove burrs and make it truly round.
CAUTION:
Clean away shavings from reamed hole.
Special Tool
(A): 09916-37320
(B): 09916-34542
2) Using special tools, install valve guide to cylinder head as follows.
Special Tool
(A): 09916-58210
(B): 09916-56510
NOTE:
^ Never reuse valve guide.
Install new oversized valve guide.
^ Intake and exhaust valve guides are identical.
a) Heat cylinder head uniformly to a temperature of 80 to 100°C (176 to 212°F) so that it will not be distorted, and drive new valve guide into guide hole with special tools.
b) Drive in new valve guide until special tool contacts cylinder head.
After installation, make sure that valve guide protrudes by specified dimension "a" from cylinder head.
CAUTION:
For installing intake valve guide and exhaust valve guide, the same special tool (B) is used, but its application direction is different. Use it in proper direction.
^ For intake valve guide
The side (2) should be directed to valve guide.
^ For exhaust valve guide
The side (1) should be directed to valve guide.
Valve guide protrusion "a"
IN: 16.3 - 16.7 mm (0.642 - 0.657 in.)
EX: 12.3 - 12.7 mm (0.485 - 0.500 in.)
3) Ream valve guide bore with special tool.
CAUTION:
Clean away shavings from reamed hole.
Special Tool
(A): 09916-34550
(B): 09916-34542
4) Install valve spring seat to cylinder head.
5) Install new valve stem seal (1) to valve guide.
After applying engine oil to valve stem seal and spindle of special tool (A), fit valve stem seal to spindle, and then install valve stem seal to valve guide pushing special tool by hand.
After installation, check that valve stem seal is properly fixed to valve guide.
CAUTION:
When installing, never tap or hit special tool with a hammer or else. Install seal to guide only pushing special tool by hand.
Tapping or hitting special tool may cause damage to seal.
Special Tool
(A): 09917-98221
(B): 09916-58210
6) Apply engine oil to valve stem seal, valve guide bore and valve stem.
7) Install valve to valve guide.
8) Install valve spring and valve spring retainer.
NOTE:
Valve spring does not have specific direction for installation.
9) Using special tools, compress valve spring and fit two valve cotters (1) into groove in valve stem.
CAUTION:
When compressing the valve spring, be careful not to damage inside surface of tappet installing hole.
Special Tool
(A): 09916-14510
(B): 09916-14522
(C): 09916-84511
10) Install venturi plug (1).
Tightening torque
Venturi plug (a): 3.5 Nm (0.36 kg-m, 2.5 lbf-ft)
