Repair Instruction - Customize Parameters
INTRODUCTION: REPAIR INSTRUCTION: CUSTOMIZE PARAMETERS
CUSTOMIZE PARAMETERS
HINT: The following items can be customized.
NOTICE:
- When the customer requests a change in a function, first make sure that the function can be customized.
- Be sure to make a note of the current settings before customizing.
- When troubleshooting a function, first make sure that the function is set to the default setting.
1. POWER DOOR LOCK CONTROL SYSTEM
Door Lock
Illuminated Entry
2. WIRELESS DOOR LOCK CONTROL SYSTEM (w/ Smart Key System)
Wireless Door Lock Control System
3. WIRELESS DOOR LOCK CONTROL SYSTEM (w/o Smart Key System)
Wireless Door Lock Control System
4. SMART KEY SYSTEM (for Entry Function)
Smart Key
(a) ENTRY UNLOCK MODE SWITCHING
(1) To change the vehicle entry unlock mode, make sure that the vehicle power is off and simultaneously push and hold the key lock switch and another key switch for 5 seconds.
Driver door unlock default setting:
When the switches are pressed and held for 5 seconds, the entry door unlock mode changes to the mode that is not currently selected.
NOTICE: After pressing and holding the switches for 5 seconds, wait 5 seconds before performing the same procedure again.
- Driver door unlock mode:
When the driver door touch sensor is touched, only the driver door unlocks. When another touch sensor is touched, all doors unlock.
- All door unlock mode:
When any touch sensor is touched, all doors unlock.
(2) The certification ECU (smart key ECU assembly) receives this signal from the door control receiver assembly and changes the smart key system to the entry unlock mode.
(3) The certification ECU (smart key ECU assembly) sounds the buzzers of the wireless door lock buzzer and combination meter to inform the user that the mode has been changed.
HINT: The procedure only changes the entry unlock mode of the smart key system. It does not switch the unlocking of the wireless door lock control.
(b) ELECTRICAL KEY CANCEL
The electrical key cancel operation disables the following functions:
- Entry Unlock/Lock
- Entry Ignition
- Entry Back Door Open
- Electrical Key Lock-in Prevention
- Warning
(1) The operation procedures are as follows:
Precondition:
Engine switch off, driver side door closed and unlocked.
1. Push the unlock switch of the key once.
2. Open the driver door within 5 seconds.
3. Push the unlock switch of the key twice within 5 seconds.
4. Close and open the driver door twice within 30 seconds.
(Driver door: Close -> Open -> Close -> Open)
5. Push the unlock switch of the key twice within 5 seconds.
6. Close and open the driver door within 30 seconds.
(Driver door: Close -> Open)
7. Close the driver door within 5 seconds.
When electrical key cancel is activated, the wireless door lock buzzer sounds twice.
To return to the original condition, perform the procedures again. When the original condition is returned, the wireless door lock buzzer sounds once.
5. SMART KEY SYSTEM (for Start Function)
Smart Key
(a) CUSTOMIZING FUNCTION WITHOUT TECHSTREAM
Performing the following procedure disables the smart key system.
HINT: To start the engine while the smart key system is disabled, follow the procedure for when the key battery is low Smart Key System (for Start Function).
(1) The procedure to disable the smart key system is as follows:
HINT: Repeating the following steps switches the smart key system status between activated and disabled.
Preconditions:
Engine switch off, driver door closed and unlocked.
1. Press the unlock switch of the key once.
2. Open the driver door within 5 seconds after pressing the unlock switch of the key in the previous step.
3. Repeat closing and opening of the driver door twice within 30 seconds after opening the driver door in the previous step.
4. Press the unlock switch of the key twice within 30 seconds after the last closing of the driver door in the previous step.
5. Close and then open the driver door within 30 seconds after pressing the unlock switch of the key twice in the previous step.
6. Close the driver door within 5 seconds after opening the driver door in the previous step.
7. Check that the wireless buzzer sounds once*1 or twice*2.
- *1: When the smart key system status is changed from activated to disabled.
- *2: When the smart key system status is changed from disabled to activated.
6. THEFT DETERRENT SYSTEM (w/ Smart Key System)
Security
7. THEFT DETERRENT SYSTEM (w/o Smart Key System)
Security
8. LIGHTING SYSTEM (INT)
Illuminated Entry
HINT:
- *1: w/o Smart Key System
- *2: w/ Smart Key System
9. METER/GAUGE SYSTEM
Combination Meter
- *1: This setting is only valid for the buzzer which sounds at 20 km/h (12 mph) or more.
10. SEAT BELT WARNING SYSTEM
Combination Meter
HINT: This setting is only valid for the buzzer which sounds at 20 km/h (13 mph) or more.
11. AIR CONDITIONING SYSTEM (for Automatic Air Conditioning System)
Air Conditioner
12. POWER BACK DOOR SYSTEM
Power Back Door System
- *:The warning buzzer that sounds, when the power back door is operating cannot be customized. (Even if this function is set to "off", the buzzer will still sound.)
13. LIGHTING SYSTEM (EXT)
Light Control
