Programmable Customer Parameters
Programmable customer parameters
Introduction
General
This is a summary of the customer parameters for the S40/V40 which are programmable in VIDA. The summary also contains information about control modules that require reprogramming when they are replaced. In most cases this document refers to existing information.
Combined instrument panel, model year 1999-
General
A new combined instrument panel must be programmed with two PIN codes (model year 1999 only one PIN code) and certain customer settings need to be entered before it will work. From the 2000 model year certain values are programmed into the combined instrument panel using the VIDA software.
For a summary see Description of programmed data Description Of Programmed Data.
Programming can be found in VIDA vehicle communication, function group 3.
Lock and alarm (VGLA), model year 2000-
General
A new VGLA control module must be programmed with three PIN codes, remote controls and lock types, and certain customer settings need to be entered before it will work. All values are programmed in via VIDA software.
Programming can be found in VIDA vehicle communication, function group 3.
Remote control
The control module memory has room for three remote controls. If the car is equipped with an alarm, two remote controls are programmed into the control module memory. An additional remote control can be programmed into the control module memory without needing to reprogram the control module. It is possible to add a new remote control by erasing old ones (for example if a remote control is broken or has been lost). It is also possible to read off the number of remote controls programmed. Cars without an alarm can also have remote controls.
Programming can be found in VIDA vehicle communication, function group 3.
Lock type
Three types of lock can be programmed:
- KCL, central locking only controlled by keys
- RCL, central locking with remote control RDL, central locking with remote control and Deadlock function
- 2STEP, central locking with remote control and two stage unlocking function.
In addition, the PCL childlock function can be programmed. The programmed lock type can also be read off.
To program deadlocking and PCL, the car must have the correct lock units.
Programming can be found in VIDA vehicle communication, function group 3.
Lock and alarm functions
For a summary see Description of the programmed values Description Of The Programmed Values.
Programming can be found in VIDA vehicle communication, function group 3.
Immobilizer, model year 2000-
General
A new immobilizer control module must be programmed with one PIN code and the ignition keys before it will work. All values are programmed in via VIDA software.
Programming can be found in VIDA vehicle communication, function group 3.
Adding / erasing ignition keys
Add keys
This function is used when the customer has ordered new keys. The key code for the extra key must be programmed into the control module before the key can be used to start the car. The control module memory has room for six key codes.
Erase key
This function is used when the customer wants to exclude one or more keys from starting the car. These may be lost or stolen keys which could be traced back to the car. All programmed keys are erased from the control module memory. The remaining keys are then reprogrammed into the control module memory again. It is important that the customer takes all the keys to the workshop.
Programming can be found in VIDA vehicle communication, function group 3.
Electronic climate control (ECC), model year 2001-
General
Certain customer settings can be changed for a new electronic climate control (ECC) module.
For a summary
Programming can be found in VIDA vehicle communication, function group 8
Central electronic module (CEM), model year 2000-
General
Certain customer settings can be changed for a new central electronic module.
For a summary see Description of programmed data Description Of Programmed Data.
Programming can be found in VIDA vehicle communication, function group 3.
Additional heater and parking heater 912
Programming outside temperature (start temperature)
The outside temperature (start temperature) for the additional heater can be reprogrammed. The start value can be changed within the limits of 0°C to +10°C. The factory setting is +4°C. This allows the start temperature to be adjusted to the customer wishes.
The temperature is programmable between 0° and +10°C in steps of 1°C.
Programming can be found in VIDA vehicle communication, function group 8.
Engine management system, EMS2000
Programming a new control module
PIN codes must be programmed into the control module after a new EMS 2000 engine control module (ECM) has been installed in the car. The PIN codes are retrieved from the Volvo central database. The new control module must be installed in the car before this programming is carried out. The malfunction indicator lamp (MIL) will flash on a new control module until the programming is complete.
Programming can be found in VIDA vehicle communication, function group 2.
Engine management system, Melco 2 (B4184SJ)
Programming a new control module
PIN codes must be programmed into the control module after a new Melco 2 engine control module (ECM) has been installed in the car. The PIN codes are retrieved from the Volvo central database. The new control module must be installed in the car before this programming is carried out. The malfunction indicator lamp (MIL) will flash on a new control module until the programming is complete.
Programming can be found in VIDA vehicle communication, function group 2.
Programming the cruise control
Function for programming the control module with or without cruise control.
Programming can be found in VIDA vehicle communication, function group 2.
Engine management system, MSA 15.5 (D4192T2) / EDC 15C (D4192T3/T4)
Programming a new control module (only D4192T3/T4)
PIN codes must be programmed into the control module after a new EDC 15C engine control module (ECM) has been installed in the car. The PIN codes are retrieved from the Volvo central database. The new control module must be installed in the car before this programming is carried out.
Programming can be found in VIDA vehicle communication, function group 2.
Programming the cruise control
Function for programming the control module with or without cruise control.
Programming can be found in VIDA vehicle communication, function group 2.