Programming The Remote Control Function
Programming the remote control function
Connecting VCT2000
Connecting the Volvo Communication Tool 2000 (VCT 2000)
Connecting the Volvo Communication Tool 2000 (VCT 2000)
The VCT 2000 must be connected to both the VIDA PC and the data link connector (DLC) in the car to communicate with the control modules in the car.
For information about connection, see Connecting VCT2000 Connecting VCT2000.
Location of Components DSA, Data Link Connector DLC:
Select Continue.
Continue - DONE
------------------------
DONE - Conditions
-------------------------------------------------
Conditions
Conditions
Conditions
- Ignition on.
Warning! The battery must supply sufficient voltage throughout the transfer.A battery charger should therefore be connected to the vehicle throughout the transfer process.
Warning! Leave VCT 2000 connected to the vehicle until VIDA displays that the program transfer is complete.
If the transfer is interrupted (this may occur if the connection between VCT 2000 and the vehicle is broken or if the battery discharges), the status of the control module may be indefinable. It is normally sufficient to switch the ignition on and off and to then try programming again to return to normal function.
In some cases it may be necessary to disconnect the control module and then switch of the ignition to return to normal function.
Caution! It is important that correct chassis number is supplied when ordering software. If an incorrect chassis number is supplied, the software may contain incorrect PIN codes. This will mean that the control module cannot be programmed.If programming fails, even though the correct software has been ordered, there may be an incorrect PIN code stored in VITaL.
Select Continue.
Continue - DONE
------------------------
DONE - Communication test
-------------------------------------------------
Communication test
Verification of communication with the control module
Communication with the control module must be verified!
Please wait!
Numeric Result 0 - DONE
Numeric Result -32000 - Communication fault
Numeric Result -32008 - Communication fault
Numeric Result -33000 - Communication fault
Numeric Result 24577 - Communication fault
Numeric Result 25345 - Communication fault
Numeric Result 25419 - Communication fault
Numeric Result 25456 - Communication fault
Numeric Result 25468 - Communication fault
------------------------
Communication fault
The communication between VCT 2000 and the vehicle has failed for one of the following reasons:
- The battery voltage is too low.
- The control module does not respond.
- The ignition is off.
Ensure that:
Battery voltage exceeds 12 V.
The ignition is on.
Do you want to try to establish communication again?
Yes - Verification of communication with the control module
No - No Fault Found
------------------------
Communication fault
Communication failure
Communication between VIDA PC and VCT 2000 has failed for one of the following reasons:
- Ignition is OFF.
- The VST/VCT 2000 switch is not in position VCT 2000.
- VCT 2000 is not connected to the diagnostic connector.
- VCT 2000 is not connected to VIDA PC/selector switch.
- Communication problem in VIDA application and/or vehicle.
- Too low battery voltage.
Ensure that:
- Ignition is ON and selector switch is in position VCT 2000.
- VCT 2000 is properly connected to diagnostic connector inside vehicle and VIDA PC/selector switch.
- VCT 2000 and associated cables are functional.
- Battery voltage exceeds 12 V.
Do you want to make another attempt to establish communication?
Yes - YES
No - NO
------------------------
YES - Verification of communication with the control module
NO - No Fault Found
-------------------------------------------------
DONE - Information about programming the remote control function
No Fault Found - DONE
-------------------------------------------------
Information about programming the remote control function
The control module has functions that allow remote controls to be added. Lock type programming and then remote control programming are also included in this procedure.
Model year 2003-: For cars with an integrated ignition key / remote control
The head of the integrated ignition key / remote control ( see illustration) contains functions for both the immobilizer and the remote control. This means that for a new unprogrammedignition key / remote control both the immobilizer control module and VGLA control module must be programmed with the functions for the immobilizer and remote control. After this procedure, order the software package to program the ignition key. However the immobilizer control module is still limited to storing a maximum of six keys. The VGLA control module is restricted to three remote controls.
Select one of the following functions
1. Add the remote control function (and programming of lock type)
2. Exit without programming.
1 - Information about programming the lock function
2 - DONE
-------------------------------------------------
Information about programming the lock function
A number of lock types can be programmed. To add the remote control function, the lock type must be changed from KCL to RCLor from KCL+PCL to RCL+PCL. Other lock types cannot be modified for this function.
Note! Note that the programming must correspond to the type of lock motors that the car is equipped with
Lock type abbreviations
- KCL (Key Central Lock), central locking only controlled by keys
- PCL (Power Child Lock), additional lock motors for childproof locking of the rear passenger doors
- RCL (Remote Central Lock), central locking with remote controls.
Select Continue.
Continue - Program the lock type
-------------------------------------------------
Program the lock type
- Ignition on.
Programming must be carried out according to one of the options below:
- From KCL (central locking only controlled by keys) to RCL (central locking with remote controls)
- From KCL+PCL (central locking only controlled by keys and additional lock motors for childproof locking of the rear passenger doors) to RCL+PCL (central locking with remote controls and additional lock motors for childproof locking of the rear passenger doors).
1. Select the VCT2000 symbol to begin the programming procedure
2. Read off the current value for the type of lock in the upper list box
3. To modify the Lock type, select the desired lock type from the alternatives in the lower list window
4. Select start to begin the programming procedure
5. Check that the new programmed lock type in the upper list box is correct.
If the selected setting is incorrect, click on the desired value in the lower list box again. Then click on the Start programming button. Check that the new value in the upper list box is the desired value.
Select "Continue" when you are ready.
Continue - Information about programming remote controls
Continue - Information
-------------------------------------------------
Information
Note! This is a newVGLA control module.The add remote control function cannotbe used on new, unprogrammed control modules.
Select "Continue". Order the correct software package for a newVGLA control module.
Continue - DONE
-------------------------------------------------
Information about programming remote controls
The control module has code positions for 3 remote controls.
When the control module receives a remote code during programming, the code is stored in the control module memory.
The customer must take all the remote controls to the workshop if he/she wants all the remote controls programmed.
Continue - Program remote controls
-------------------------------------------------
Program remote controls
Caution! Model year 2003-.The driver's door must be closed when reprogramming the remote control. If the driver's door is open the remote control reciever will not receive signals from the remote control.
- Ignition on
- Driver's door closed (Only model year 2003-)
- Select the VCT2000 symbol to begin the programming procedure
- Have the first remote control to be programmed into the control module ready
- Then select Start
- Keep an eye on the screen and press the correct remote control button as soon as the message is displayed. Wait!
A - Information
B - Information
D - Information
-------------------------------------------------
Information
Note! The remote control is now programmed into the control module!
- Ignition on.
Select the VCT2000 symbol to read off the number of programmed remote controls.
The control module has code positions for 3 remote controls.
Do you want to program more remote controls?
Yes - Program remote controls
No - Information
-------------------------------------------------
Information
Note! The remote control has notbeen programmed into the control module!The control module has not received the code from the remote control.
Do you want to try again?
Yes - Program remote controls
No - Information
-------------------------------------------------
Information
Note! The control module memory for remote controls is now full.
- Ignition on.
All positions for remote controls have been used in the control module memory. No more remote controls can be programmed into the memory if there are no free positions.
Select the VCT2000 symbol to read off the current status of the remote control memory.
Select Continue.
Continue - Information
-------------------------------------------------
Information
Is there any further programming to be carried out?
Yes - Information about programming the remote control function
No - DONE
-------------------------------------------------