Add the Trip Computer Function
Add the trip computer function
Connecting the Volvo Communication Tool 2000 (VCT2000)
Connecting the Volvo Communication Tool 2000 (VCT 2000)
Connecting the Volvo Communication Tool 2000 (VCT 2000)
The VCT 2000 must be connected to both the VIDA PC and the data link connector (DLC) in the car to communicate with the control modules in the car.
For information about connection, see Connecting VCT2000 Connecting VCT2000.
Location of Components DSA, Data Link Connector DLC:
Continue - DONE
------------------------
DONE - Conditions
-------------------------------------------------
Conditions
Conditions
Conditions
- Ignition on.
Warning! The battery must supply sufficient voltage throughout the transfer.A battery charger should therefore be connected to the vehicle throughout the transfer process.
Warning! Leave VCT 2000 connected to the vehicle until VIDA displays that the program transfer is complete.
If the transfer is interrupted (this may occur if the connection between VCT 2000 and the vehicle is broken or if the battery discharges), the status of the control module may be indefinable. It is normally sufficient to switch the ignition on and off and to then try programming again to return to normal function.
In some cases it may be necessary to disconnect the control module and then switch of the ignition to return to normal function.
Caution! It is important that correct chassis number is supplied when ordering software. If an incorrect chassis number is supplied, the software may contain incorrect PIN codes. This will mean that the control module cannot be programmed.If programming fails, even though the correct software has been ordered, there may be an incorrect PIN code stored in VITaL.
Continue - DONE
------------------------
DONE - Communication test
-------------------------------------------------
Communication test
Verification of communication with the control module
Communication with the control module must be verified!
Please wait!
Numeric Result 0 - DONE
Numeric Result -32000 - Communication fault
Numeric Result -32008 - Communication fault
Numeric Result -33000 - Communication fault
Numeric Result 24577 - Communication fault
Numeric Result 25345 - Communication fault
Numeric Result 25419 - Communication fault
Numeric Result 25456 - Communication fault
Numeric Result 25468 - Communication fault
------------------------
Communication fault
The communication between VCT 2000 and the vehicle has failed for one of the following reasons:
- The battery voltage is too low.
- The control module does not respond.
- The ignition is off.
Ensure that:
Battery voltage exceeds 12 V.
The ignition is on.
Do you want to try to establish communication again?
Yes - Verification of communication with the control module
No - No Fault Found
------------------------
Communication fault
Communication failure
Communication between VIDA PC and VCT 2000 has failed for one of the following reasons:
- Ignition is OFF.
- The VST/VCT 2000 switch is not in position VCT 2000.
- VCT 2000 is not connected to the diagnostic connector.
- VCT 2000 is not connected to VIDA PC/selector switch.
- Communication problem in VIDA application and/or vehicle.
- Too low battery voltage.
Ensure that:
- Ignition is ON and selector switch is in position VCT 2000.
- VCT 2000 is properly connected to diagnostic connector inside vehicle and VIDA PC/selector switch.
- VCT 2000 and associated cables are functional.
- Battery voltage exceeds 12 V.
Do you want to make another attempt to establish communication?
Yes - YES
No - NO
------------------------
YES - Verification of communication with the control module
NO - No Fault Found
-------------------------------------------------
DONE - Information about programming the trip computer function
No Fault Found - DONE
-------------------------------------------------
Information about programming the trip computer function
Note! This programming must not be carried out on a new unprogrammed combined instrument panel. Exit. Order the correct software package for a new combined instrument panel.
This option is used to program the combined instrument panel for the trip computer function. Before programming is carried out, the unit for the outside temperature sensor must be installed and connected. A diagnostic trouble code (DTC) will be stored if programming is carried out when an outside temperature sensor is not installed.
If the display is already activated, select alternative 1 below.
If the display is notalready activated, select alternative 2 below.
Select one of the following functions:
1. Programming the trip computer function
2. Activating the display
3. Exit programming.
1 - Programming the trip computer function
2 - Programming the display type
3 - DONE
-------------------------------------------------
Programming the display type
Note! This parameter is used to set whether the combined instrument panel display will be activated or not. This function must be used if a display has not previously been activated.
- Ignition on.
1. Click the VCT2000 symbol to activate the programming procedure
2. Read off the current value for the setting in the upper list windows
3. To modify the Display type, select the desired setting from the alternatives in the lower list window.
Caution! If the combined instrument panel display is in kilometers, the kilometer display (metric) must be selected.If the combined instrument panel display is in miles, the miles display (imperial) must be selected.
4. Select the Start programming button to begin the programming procedure
5. Check that the new setting in the middle list window is correct.
If the selected setting is incorrect, click on the desired value in the lower list box again. Then click on the Start programming button. Check that the new value in the middle list window is the desired value.
Then select Continue
Continue - Programming the outside temperature display unit
-------------------------------------------------
Programming the outside temperature display unit
Note! Use this parameter to set the outside temperature unit to display readings in °C or °F.
Caution! This programming is only relevant if the display for outside temperature / trip computer function is installed / programmed.
- Ignition on.
1. Click the VCT2000 symbol to activate the programming procedure
2. Read off the current value for the setting in the upper list box
3. If you want to modify the Unit for temperature display, select the desired setting from the alternatives in the lower list window
4. Select the Start programming button to begin the programming procedure
5. Check that the new setting in the upper list box is correct.
Continue - Programming the trip computer function
-------------------------------------------------
Programming the trip computer function
Note! This parameter is used to set whether the combined instrument panel has the trip computer function or not.
- Ignition on.
1. Click the VCT2000 symbol to activate the programming procedure
2. Read off the current value for the setting in the upper list box
3. To modify the Trip computer function, select the desired settings from the alternatives in the lower list window
4. Select the Start programming button to begin the programming procedure
5. Check that the new setting in the upper list box is correct.
If the selected setting is incorrect, click on the desired value in the lower list box again. Then click on the Start programming button. Check that the new value in the upper list box is the desired value.
Then select Continue
Continue - Information
-------------------------------------------------
Information
Is there any further programming to be carried out?
Yes - Information about programming the trip computer function
No - DONE
-------------------------------------------------