Operation CHARM: Car repair manuals for everyone.
Home >> Volvo >> 2003 >> V40 L4-1.9L Turbo VIN 27 B4204T4 >> Repair and Diagnosis >> Accessories and Optional Equipment >> Antitheft and Alarm Systems >> Testing and Inspection >> Programming and Relearning >> Modify the VGLA settings >> Part 2

Part 2






Modify the VGLA settings (Continued)

Programming the glass breakage sensor

Note! Displays whether the control module is configured for a glass breakage sensor or not.The alarm must be activated before the glass breakage sensor function will work.




- Ignition on.
1. Select the VCT2000 symbol to begin the programming procedure
2. Read off the present value for the setting in the upper list box
3. If you want to modify the Glass breakage sensor, select the desired setting from the alternatives in the lower list window
4. Select the Start programming button to begin the programming procedure
5. Check that the new setting in the upper list box is correct.
If the selected setting is incorrect, click on the desired value in the lower list box again. Then click on the Start programming button. Check that the new value in the upper list box is the desired value.









Do you wish to continue to program the next setting?

Yes - Programming alarm deactivation for the immobilizer

No - Information

-------------------------------------------------

Programming alarm deactivation for the immobilizer

Note! The VGLA control module receives a signal from the immobilizer control module indicating whether the ignition key in the ignition switch is approved (approved key code) or not when the ignition is switched on. This parameter governs whether or not the VGLA control module will deactivate the alarm if the immobilizer control module approves the ignition key in the ignition switch.The alarm must be activated before the alarm deactivation function will work.




- Ignition on.
1. Select the VCT2000 symbol to begin the programming procedure
2. Read off the present value for the setting in the upper list box
3. If you want to modify the Alarm deactivation for the immobilizer, select the desired setting from the alternatives in the lower list window
4. Select the Start programming button to begin the programming procedure
5. Check that the new setting in the upper list box is correct.
If the selected setting is incorrect, click on the desired value in the lower list box again. Then click on the Start programming button. Check that the new value in the upper list box is the desired value.










Do you wish to continue to program the next setting?

Yes - Programming the tilt sensor

No - Information

-------------------------------------------------

Programming the tilt sensor

Note! Displays whether the control module is configured for a tilt sensor or not.The alarm must be activated before the tilt sensor function will work.




- Ignition on.
1. Select the VCT2000 symbol to begin the programming procedure
2. Read off the present value for the setting in the upper list box
3. If you want to modify the Tilt sensor, select the desired setting from the alternatives in the lower list window
4. Select the Start programming button to begin the programming procedure
5. Check that the new setting in the upper list box is correct.
If the selected setting is incorrect, click on the desired value in the lower list box again. Then click on the Start programming button. Check that the new value in the upper list box is the desired value.









Do you wish to continue to program the next setting?

Yes - Programming the Immobilizer LED

No - Information

-------------------------------------------------

Programming the Immobilizer LED

Note! This parameter controls the LED function on the dashboard which displays that the immobilizer system is activated when the ignition is switched off. This only applies if the car is not equipped with an alarm. This function is market dependent. Contact the dealer if unsure about this function.




- Ignition on.
1. Select the VCT2000 symbol to begin the programming procedure
2. Read off the present value for the setting in the upper list box
3. If you want to modify the Immobilizer LED, select the desired setting from the alternatives in the lower list window
4. Select the Start programming button to begin the programming procedure
5. Check that the new setting in the upper list box is correct.
If the selected setting is incorrect, click on the desired value in the lower list box again. Then click on the Start programming button. Check that the new value in the upper list box is the desired value.









Do you wish to continue to program the next setting?

Yes - Programming diagnostic trouble code (DTC) indication

No - Information

-------------------------------------------------

Programming diagnostic trouble code (DTC) indication

Note! This parameter controls whether the indicator LED on the dashboard should display that a diagnostic trouble code (DTC) is stored or not.The alarm must be activated before the indication function will work.




- Ignition on.
1. Select the VCT2000 symbol to begin the programming procedure
2. Read off the present value for the setting in the upper list box
3. If you want to modify the DTC indication, select the desired setting from the alternatives in the lower list window
4. Select the Start programming button to begin the programming procedure
5. Check that the new setting in the upper list box is correct.
If the selected setting is incorrect, click on the desired value in the lower list box again. Then click on the Start programming button. Check that the new value in the upper list box is the desired value.









Do you wish to continue to program the next setting?

Yes - Programming automatic alarm activation

No - Information

-------------------------------------------------

Programming automatic alarm activation

Note! This parameter controls the automatic alarm activation. This means that the alarm is activated when the ignition is switched off, the driver's door opened and closed and all the other doors are closed. This function requires that the car is equipped with an alarm. This function is market dependent. Contact the dealer if unsure about this function.The alarm must be activated before the alarm activation function will work.




- Ignition on.
1. Select the VCT2000 symbol to begin the programming procedure
2. Read off the present value for the setting in the upper list box
3. To modify the Setting for automatic alarm activation, select the desired setting from the alternatives in the lower list box
4. Select the Start programming button to begin the programming procedure
5. Check that the new setting in the upper list box is correct.
If the selected setting is incorrect, click on the desired value in the lower list box again. Then click on the Start programming button. Check that the new value in the upper list box is the desired value.










Do you wish to continue to program the next setting?

Yes - Program key controlled alarm activation

No - Information

-------------------------------------------------

Program key controlled alarm activation

Note! This parameter controls the function for activating / deactivating the alarm using the key in the driver's door lock. This function is market dependent. Contact the dealer if unsure about this function.The alarm must be activated before the alarm activation function will work.




- Ignition on.
1. Select the VCT2000 symbol to begin the programming procedure
2. Read off the present value for the setting in the upper list box.
The Key controlled alarm activation and Key controlled alarm deactivation options are linked. They must always have the same status value. If one of the options is modified the other will automatically be assigned the same value
3. To modify the Setting for key controlled alarm (de)activation, select the desired setting from the alternatives in the lower list box
4. Select the Start programming button to begin the programming procedure
5. Check that the new setting in the upper list box is correct.
If the selected setting is incorrect, click on the desired value in the lower list box again. Then click on the Start programming button. Check that the new value in the upper list box is the desired value.










Do you wish to continue to program the next setting?

Yes - Programming the panic alarm

No - Information

-------------------------------------------------

Programming the panic alarm

Note! This parameter controls the function used for triggering the alarm with the remote control. The function requires that the remote control is equipped with an extra red button.The alarm must be activated before the panic alarm function will work.




- Ignition on.
1. Select the VCT2000 symbol to begin the programming procedure
2. Read off the present value for the setting in the upper list box
3. To modify the Panic alarm setting, select the desired setting from the alternatives in the lower list box
4. Select the Start programming button to begin the programming procedure
5. Check that the new setting in the upper list box is correct.
If the selected setting is incorrect, click on the desired value in the lower list box again. Then click on the Start programming button. Check that the new value in the upper list box is the desired value.










Do you wish to continue to program the next setting?

Yes - Programming alarm deactivation via the central locking switch

No - Information

-------------------------------------------------

Programming alarm deactivation via the central locking switch





Programming alarm deactivation via the central locking switch

Programming alarm deactivation via the central locking switch

Caution! Applies only from model year 2001 inclusive.

Note! This parameter controls the function for alarm activation via the central locking switch. This function is market dependent. Contact the dealer if unsure about this function.




- Ignition on.
1. Select the VCT2000 symbol to begin the programming procedure
2. Read off the current value for the setting in the upper list box
3. If you want to modify the Alarm activation, select the desired setting from the alternatives in the lower list window
4. Select start to begin the programming procedure
5. Check that the new programmed setting in the upper list box is correct.
If the selected setting is incorrect, click on the desired value in the lower list box again. Then click on the Start programming button. Check that the new value in the upper list box is the desired value.









Do you wish to continue to program the next setting?

Yes - ANOTHER TEST

No - DONE

------------------------

ANOTHER TEST - Programming continuous alarm activation

DONE - Information

-------------------------------------------------

Programming continuous alarm activation





Programming continuous alarm activation

Programming continuous alarm activation

Caution! Applies only from model year 2001 inclusive.

Note! This parameter controls the function for continuous alarm if any of the doors, hood or tailgate are opened when the alarm is activated. If set to continuous alarm, the siren sounds 10 times at 30-second intervals. This occurs if a door, the hood or tailgate/rear door is opened during an attempted break in. When continuous alarming is selected, the siren sounds for only 30 seconds (1 interval) at an attempted break in caused by an open door, hood or tailgate/rear door. This function is market dependent. Contact the dealer if unsure about this function.




- Ignition on.
1. Select the VCT2000 symbol to begin the programming procedure
2. Read off the current value for the setting in the upper list box
3. If you want to modify the Continuous alarm activation, select the desired setting from the alternatives in the lower list window
4. Select start to begin the programming procedure
5. Check that the new programmed setting in the upper list box is correct.
If the selected setting is incorrect, click on the desired value in the lower list box again. Then click on the Start programming button. Check that the new value in the upper list box is the desired value.









Do you wish to continue to program the next setting?

Yes - ANOTHER TEST

No - DONE

------------------------

ANOTHER TEST - Information about programming the lock function

DONE - Information

-------------------------------------------------

Information about programming the lock function
A number of lock types can be programmed.

Note! Note that the programming must correspond to the type of lock motors that the car is equipped with.

Abbreviations
- KCL (Key Central Lock)
- PCL (Power Child Lock)
- RCL (Remote Central Lock)
- RDL (Remote Dead Lock).

The following types of lock can be programmed:
- KCL, central locking only controlled by keys
- KCL+PCL, central locking only controlled by keys and additional lock motors for childproof locking of the rear passenger doors
- RCL, central locking with remote controls
- RCL+PCL, central locking with remote controls and additional lock motors for childproof locking of the rear passenger doors
- RDL, central locking with remote control and deadlock function
- RDL+PCL, central locking with remote control and deadlock function, and additional lock motors for childproof locking of the rear passenger doors
- 2-STEP central locking with a function that requires two impulses from the remote control or key to unlock all doors. One impulse only opens the driver's door.





Continue - Program the lock type

-------------------------------------------------

Program the lock type

Note! Note that the programming must correspond to the type of lock motors that the car is equipped with




- Ignition on.
1. Select the VCT2000 symbol to begin the programming procedure
2. Read off the current value for the type of lock in the upper list box
3. If you want to modify the Lock type, select the desired lock type from the alternatives in the lower list window
4. Select start to begin the programming procedure
5. Check that the new programmed lock type in the upper list box is correct.
If the selected setting is incorrect, click on the desired value in the lower list box again. Then click on the Start programming button. Check that the new value in the upper list box is the desired value.









Continue - Information

-------------------------------------------------

Information





Is there further programming or programmed data to be read off?

Yes - Program the VGLA alarm settings

No - DONE

-------------------------------------------------

pro multis · About Operation CHARM