Signal Too Low
Signal too low
Checking software
Checking software
Checking software
Note! The information below only applies to modal year 2003-2004.For other model years, select the alternative "No".
It may be possible to remedy the fault by downloading new software into the control module.
Action
- Go to the tab software and program the control module with the latest software.
Other information
- For more information, see Design and Function.
Has the fault been remedied?
Yes - Fault Found
No - No Fault Found
------------------------
FAULT FOUND - Fault Found
No Fault Found - front heated oxygen sensor (HO2S), heating
-------------------------------------------------
DTC status ECM-2110, front heated oxygen sensor (HO2S), heating
Note! When reading off the diagnostic trouble code (DTC) status, other stored diagnostic trouble codes (DTCs) and their status will also be listed.
Read off the diagnostic trouble code (DTC) status. Check the status of the relevant diagnostic trouble code (DTC).
Was the status of the relevant diagnostic trouble code (DTC) permanent?
Yes - Checking the wiring and component
No - Checking wiring and connectors
-------------------------------------------------
Checking wiring and connectors
Check the cable between front heated oxygen sensor (HO2S) terminal #1 and the system relay. Check for an intermittent open-circuit.
Check the cable between control module terminal #A18 and front heated oxygen sensor (HO2S) terminal #2. Check for an intermittent open-circuit.
Other information
- Checking wiring and terminals. Intermittent faults Checking Wiring and Terminals. Intermittent Faults
- Connecting the breakout box Connecting the Breakout Box
- Heated oxygen sensor (HO2S), replacing Heated Oxygen Sensor (HO2S), Replacing
- Signal specification Signal Description / Specification
Continue - Fault-tracing information
-------------------------------------------------
Fault-tracing information
Information
Fault-tracing information
If the fault is intermittent, do not verify fault-tracing if the fault does not recur.
It is possible to view the information again, or leave fault-tracing for this diagnostic trouble code (DTC).
Do you want to view the information again?
Yes - Attempt New Test
No - Fault Found
------------------------
Attempt New Test - front heated oxygen sensor (HO2S), heating
FAULT FOUND - DONE
DONE - DONE
-------------------------------------------------
Checking the wiring and component
Check the resistance of the front heated oxygen sensor (HO2S) element between #1 and #2. Resistance should be approximately 1.0 ohms at 20 °C.
Check the heated oxygen sensor (HO2S) connector. Check for contact resistance. Check for oxidation.
Check the cable between control module terminal #A18 and front heated oxygen sensor (HO2S) terminal #2. Check for a short-circuit to ground. Check for an open-circuit.
Check the cable between front heated oxygen sensor (HO2S) terminal #1 and the system relay. Check for an open-circuit.
Remedy as necessary.
Other information
- Checking wiring and terminals. Permanent fault Checking Wiring and Terminals. Permanent Fault
- Connecting the breakout box Connecting the Breakout Box
- Heated oxygen sensor (HO2S), replacing Heated Oxygen Sensor (HO2S), Replacing
- Signal specification Signal Description / Specification.
Continue - Verification
-------------------------------------------------
Verification
Verification
Verification
Hint: After carrying out the repair, check that the fault has been remedied.
- Ignition off
- Reconnect connectors, reinstall components
- Ignition on
- Read off the heater element resistance in the front heated oxygen sensor (HO2S).
The resistance should be 0.5-3 ohms at 20°C.
Is the value correct?
Yes - VERIFIED
No - VERIFICATION FAILED
------------------------
VERIFICATION FAILED - Fault-tracing information
VERIFIED - Fault Found
-------------------------------------------------
Fault-tracing information
Information
Fault-tracing information
The fault should have been detected and remedied. As this is not the case fault-tracing has failed.
Exit fault-tracing for this diagnostic trouble code (DTC) or make another attempt.
Do you want to exit fault-tracing?
Yes - FAULT-TRACING FAILED
No - Attempt New Test
------------------------
FAULT-TRACING FAILED - FAULT-TRACING FAILED
Attempt New Test - front heated oxygen sensor (HO2S), heating
-------------------------------------------------