Programming A New Engine Control Module (ECM), EMS 2000
Programming a new engine control module (ECM), EMS 2000
Connecting the Volvo Communication Tool 2000 (VCT 2000)
Connecting the Volvo Communication Tool 2000 (VCT 2000)
Connecting the Volvo Communication Tool 2000 (VCT 2000)
The VCT 2000 must be connected to both the VIDA PC and the data link connector (DLC) in the car to communicate with the control modules in the car.
For information about connection, see Connecting VCT2000 Connecting VCT2000.
Location of Components DSA, Data Link Connector DLC:
Continue - DONE
------------------------
DONE - Conditions
-------------------------------------------------
Conditions
Conditions
Conditions
- Ignition on.
Warning! The battery must supply sufficient voltage throughout the transfer.A battery charger should therefore be connected to the vehicle throughout the transfer process.
Warning! Leave VCT 2000 connected to the vehicle until VIDA displays that the program transfer is complete.
If the transfer is interrupted (this may occur if the connection between VCT 2000 and the vehicle is broken or if the battery discharges), the status of the control module may be indefinable. It is normally sufficient to switch the ignition on and off and to then try programming again to return to normal function.
In some cases it may be necessary to disconnect the control module and then switch of the ignition to return to normal function.
Caution! It is important that correct chassis number is supplied when ordering software. If an incorrect chassis number is supplied, the software may contain incorrect PIN codes. This will mean that the control module cannot be programmed.If programming fails, even though the correct software has been ordered, there may be an incorrect PIN code stored in VITAL.
Continue - DONE
------------------------
DONE - Communication test
-------------------------------------------------
Communication test
Verification of communication with the control module
Communication with the control module must be verified!
Please wait!
Numeric Result 0 - DONE
Numeric Result -32000 - Communication fault
Numeric Result -32008 - Communication fault
Numeric Result -33000 - Communication fault
Numeric Result 24577 - Communication fault
Numeric Result 25345 - Communication fault
Numeric Result 25419 - Communication fault
Numeric Result 25456 - Communication fault
Numeric Result 25468 - Communication fault
------------------------
Communication fault
The communication between VCT 2000 and the vehicle has failed for one of the following reasons:
- The battery voltage is too low.
- The control module does not respond.
- The ignition is off.
Ensure that:
Battery voltage exceeds 12 V.
The ignition is on.
Do you want to try to establish communication again?
Yes - Verification of communication with the control module
No - No Fault Found
------------------------
Communication fault
Communication failure
Communication between VIDA PC and VCT 2000 has failed for one of the following reasons:
- Ignition is OFF.
- The VST/VCT 2000 switch is not in position VCT 2000.
- VCT 2000 is not connected to the diagnostic connector.
- VCT 2000 is not connected to VIDA PC/selector switch.
- Communication problem in VIDA application and/or vehicle.
- Too low battery voltage.
Ensure that:
- Ignition is ON and selector switch is in position VCT 2000.
- VCT 2000 is properly connected to diagnostic connector inside vehicle and VIDA PC/selector switch.
- VCT 2000 and associated cables are functional.
- Battery voltage exceeds 12 V.
Do you want to make another attempt to establish communication?
Yes - YES
No - NO
------------------------
YES - Verification of communication with the control module
NO - No Fault Found
-------------------------------------------------
DONE - Information programming
No Fault Found - DONE
-------------------------------------------------
Information programming
This function must be used to program a new EMS 2000 engine control module (ECM)when the control module has been replaced.
The new control module must be installed in the car before this programming is carried out.
The malfunction indicator lamp (MIL) will flash on a new control module until the programming is complete.
Do you want to continue with this procedure?
Yes - Programming PIN codes into an engine control module (ECM)
No - DONE
-------------------------------------------------
Programming PIN codes into an engine control module (ECM)
Note! This function is used to program PIN codes into the engine control module (ECM).
- Ignition on.
Select the VCT 2000 symbol to begin the programming procedure.
Wait!
A - Information about successful programming
B - Information
C - Information about failed programming
-------------------------------------------------
Information about successful programming
Note! Programming complete.The EMS 2000 engine control module (ECM) is now programmed with PIN codes.
Continue - Information
-------------------------------------------------
Information about failed programming
Note! Programming failed.The EMS 2000 control module is still unprogrammed.
Do you want to make a new attempt?
Yes - Programming PIN codes into an engine control module (ECM)
No - Information
-------------------------------------------------
Information
Note! This engine control module (ECM) is already programmed. Only new control modules can be programmed with this procedure.
Continue - Information programming
-------------------------------------------------
Information
Is there any further programming to be carried out?
Yes - Information programming
No - DONE
-------------------------------------------------