Part 1
Handsfree, Volvo Handsfree System with Bluetooth
INTRODUCTION
- NOTE! Read through the whole installation instruction before starting the work.
- The front page gives the date of this edition and the edition it replaces
- The second page shows the tools needed for the installation and the contents of the installation kit
- The illustrations display the procedure in order of operation. The order of operation is repeated in the text section
- Cut out the text page in order to follow the illustrations and text at the same time.
Handsfree, Bluetooth
Note! This accessory is intended for the following vehicles:S40 2005-, Ch.No. 81143 - 2007V50 2005-, Ch.no. 78964 - 2007Wiring A is for vehicles with an internal amplifier that is located in the media player.Wiring B and C are for vehicles with an external amplifier, located on the left-hand side of the cargo compartment.Cars with Performance Sound have internal amplifier.Cars with the High Performance and Premium Sound audio systems have external amplifier.These installation instructions apply to left-hand drive vehicles. When installing in a right-hand drive vehicle, the procedure is carried out on the opposite side and/or mirrored. Where the operation differs, right-hand versions are also displayed with text and images.There may be components in the accessories kit that are not used for this installation.
Note! When installing Velcro fasteners/tape the underlying surface must be kept at a temperature of at least +20° C (68°F).Place the manual for this accessory in a suitable place in the vehicle.
Preparations
- Turn the ignition switch to position 0.
Note! Wait at least three minutes before unplugging the connectors or removing other electrical equipment.
- Open the glovebox.
- Pry off the panel in front of the center console. It is secured with two clips on each short side.
- Pull the panel away downwards.
- Apply tape to the center console to protect it during removal and installation of the glove compartment.
- Remove the panel.
- Detach the clip holding the vent from the glove compartment.
- Remove the rubber mat from the glovebox.
- Remove the five screws in the opening.
- Pull the glovebox straight back so that the two hidden clips at the upper edge release.
- Remove the outer section of the glovebox.
- Unplug the connectors on the top.
- Remove the screws for the vent.
- Pull off the vent to the right and place to one side.
- Remove the clips at the rear edge of the soundproofing panel and remove it.
- Pry off the panel at the rear edge of the center console.
- Unplug the connectors.
- Remove the screws.
- Detach the surround around the display and media player. Press in the catch in one of the upper corners of the surround using a small screwdriver. Carefully pry off the surround on the same side using a weatherstrip tool.
Note! Do not damage the panel and dashboard.
- Do the same on the other side.
Hint: If the panel is difficult to remove, press the panel on both sides again and repeat the procedure starting at the other side.
- Fold the surround backwards. Remove by pulling upwards.
- Remove the display with the infotainment control module (ICM). It is secured by two hidden clips.
Hint: Grip the control module with both hands and pull the control module straight out of the center console.
- Unplug the connectors.
- Remove the two screws.
- Remove the connector on the reverse of the center console.
- Remove the center console.
Applies to cars with manual gearbox
- Remove the gear selector lever boot from the center console. First pry it off at the front edge using a weatherstrip tool and then unhook it at the rear edge.
- Remove the two clips securing the cables to the media player by first pressing them to the sides and then pulling them away downwards.
Note! Be careful with the optic cables so that they are not bent or stretched.
- Remove the two screws from the bottom of the media player.
- Pull out the media player. Disconnect the connector on the reverse side.
Note! Note how the wiring is packed on the reverse. The fiber optic cables are easily damaged and must not be bent to a radius less than 25 mm (1").
Applies to cars with internal amplifier
- Remove cable harness A from the kit.
Applies to cars with external amplifier
- Remove cable harness B from the kit.
Applies to all models
- Connect the gray connector (2) in the new cable harness to the gray connector (3) which was detached from the media player.
- Take a 700 mm piece of foam tape and cut into three pieces of the same length. Tape one piece around connectors (2) and (3). Position these to the left, in the opening so that they are not in the way when installing the media player.
- Connect the gray connector (1) in the new cable harness to the corresponding socket in the media player.
- Pull the cable harness with the connectors down to the right-hand side of the center console.
- Plug the remaining connectors which where detached into the media player.
- Reinstall the media player and secure it.
Installing the control panel
- Clean the area on the center console as illustrated, which corresponds to the size of the double-sided adhesive tape. Use a solution of 25% isopropanol and 75% water, as well as a lint free cloth.
Dry with care, do not rub.
- Allow to dry.
Note! In cases where the area is heavily soiled or treated with cockpit shine. First clean using a washing up detergent (FAIRY or similar).
Only applies to Right-hand vehicles
- Place the control panel cable in the groove as illustrated.
- Remove the protective film on the control panel and secure according to the dimensions in the image.
- Press the cable securely into the compartment that is in the joint between the front and rear side of the center console. Stop level with the lower edge of the display opening.
- Reinstall the center console, connect the green connector and install the screws.
Applies to cars with manual gearbox
- Install the gear selector boot in the center console starting at the rear edge.
- Pull the 2 cables down on the right-hand side of the center console.
Installing the microphone
Steps 24 - 35 apply to cars up to and including model year 2006
- Tape a 700 mm length piece of foam tape on the microphone cable starting 100 mm from the microphone.
- Clean the area on the microphone and headlining panel as illustrated, which corresponds to the size of the double-sided adhesive tape. Use a solution of 25% isopropanol and 75% water, as well as a lint free cloth.
Dry with care, do not rub.
- Allow to dry.
Note! In cases where the area is heavily soiled or treated with cockpit shine. First clean using a washing up detergent (FAIRY or similar).
- Remove the backing tape from one side of the Velcro strip and press it onto the microphone.
- Remove the remaining protective film from the Velcro strip and press the microphone securely onto the ceiling panel as illustrated.
Note! Direct the microphone towards the driver.
- Remove the cover.
- Slide the rear view mirror forwards.
- Remove the screw.
- Pull the interior lighting downwards until the six hooks release and allow it to hang in place.
- Pull off the driver's weather strip at the A-post and dashboard.
- Pull off the panel from the A-pillar. The panel is secured by three clips.
- Unhook the safety clip.
- Lift the panel upwards and inwards in the vehicle.
- Remove the panel.
- Pry off the cover at the sun visor mounting.
- Detach the sun visor from its left-hand mounting.
- Remove the screw in the mounting and remove it from the roof panel.
- Remove the two screws in the right-hand mounting and detach the sun visor from the roof panel.
- Leave the sun visor in place.
- Route the cable up to the center of the front edge of the interior lighting and then up to the right.
- Route the cable into the cut-out between the roof lining and the inner section of the interior lighting.
- Route the microphone cable on top of the headlining.
- Reinstall the interior lighting.
- Check that the cable does not hang down at the front edge.
- Route the cable to the A-pillar and onwards to the glove compartment.
- Take three small tie straps from the kit and secure the cable at the A-pillar as illustrated.
- Reinstall the sun visor with the mounting and check that the cable for the sun visor does not get trapped.