Downloading Software [1 of 4]
Downloading software
Conditions for downloading software
Note! After the software download all the diagnostic trouble codes (DTCs) in the car will be automatically erased.
- VCT2000 must be connected to the vehicle.
Connecting VCT2000 Connecting The Volvo Communication Tool 2000 (VCT 2000)
- Ignition on.
Caution! The battery must be able to provide the power during the download.It is therefore recommended that a battery charger with sufficient charging capacity (at least 10 A) is connected to the vehicle to guarantee the power supply and voltage level throughout the entire download sequence.
Note! Keep the VCT2000 connected until VIDA indicates that the software download is complete.
If fault-tracing is to be carried out with the help of diagnostic trouble code (DTC) read outs, the diagnostic trouble codes (DTCs) must be read out before the downloading sequence otherwise these will be erased automatically.
To read off diagnostic trouble codes (DTCs), see VIDA vehicle communication.
Do you want to continue the downloading sequence?
Yes - OK
No - Not OK
------------------------
OK - Resetting the vehicle
Not OK - DONE
-------------------------------------------------
Resetting the vehicle
The vehicle is reset to ensure that good communication has been established.
Please wait!
Numeric Result 0 - Verifying communication
Numeric Result -200000 - Communication fault
Numeric Result -200004 - Communication fault
Numeric Result -33000 -
Numeric Result 0 -
Numeric Result 0 -
------------------------
Verifying communication
Communication with the central electronic module (CEM) is verified.
Please wait!
Numeric Result 0 - Checking battery voltage
Numeric Result -32000 -
Numeric Result -32008 -
Numeric Result -33000 -
Numeric Result 24577 - Communication fault
Numeric Result 25345 - Communication fault
Numeric Result 25419 - Communication fault
Numeric Result 25456 - Communication fault
Numeric Result 25468 - Communication fault
------------------------
Checking battery voltage
The battery voltage is checked.
Please wait!
Numeric Result 12 - Checking the position of the ignition key
Numeric Result 11 - Checking the position of the ignition key
Numeric Result 13 - Checking the position of the ignition key
Numeric Result 14 - Checking the position of the ignition key
Numeric Result 15 - Checking the position of the ignition key
Numeric Result 16 - Checking the position of the ignition key
Numeric Result 5 - Battery voltage
Numeric Result 6 - Battery voltage
Numeric Result 7 - Battery voltage
Numeric Result 8 - Battery voltage
Numeric Result 9 - Battery voltage
Numeric Result 10 - Battery voltage
------------------------
Checking the position of the ignition key
The position of the ignition key is being checked.
Please wait!
Numeric Result 6 - OK
Numeric Result 6 - Ignition key position
------------------------
Communication failure
Communication between VIDA PC and VCT 2000 has failed for one of the following reasons:
- Ignition is OFF.
- The VST/VCT 2000 switch is not in position VCT 2000.
- VCT 2000 is not connected to the diagnostic connector.
- VCT 2000 is not connected to VIDA PC/selector switch.
- Communication problem in VIDA application and/or vehicle.
- Too low battery voltage.
Ensure that:
- Ignition is ON and selector switch is in position VCT 2000.
- VCT 2000 is properly connected to diagnostic connector inside vehicle and VIDA PC/selector switch.
- VCT 2000 and associated cables are functional.
- Battery voltage exceeds 12 V.
Do you want to make another attempt to establish communication?
Yes - YES
No - NO
------------------------
YES - Resetting the vehicle
NO - Not OK
-------------------------------------------------
Communication fault
Communication with the vehicle has failed for one of the following reasons:
- The ignition key is in the wrong position
- Battery voltage too low
- The connection between the VIDA PC and VCT2000 has failed
- The connection between VCT2000 and the data link connector (DLC) has failed
- No response from the central electronic module (CEM).
Ensure that:
- The ignition is on
- Battery voltage exceeds 12 V
- VCT2000 is correctly connected to the VIDA PC
- VCT2000 is correctly connected to the data link connector (DLC) in the vehicle.
Do you want to try again?
Yes - Verifying communication
No - Not OK
-------------------------------------------------
YES - Verifying communication
NO - Not OK
-------------------------------------------------
Communication fault
The communication between VCT2000 and the vehicle has failed for one of the following reasons:
- Battery voltage too low
- No response from the central electronic module (CEM)
- The ignition is off.
Ensure that the battery voltage exceeds 12 V.
Ignition on.
Do you want to attempt to establish communication again?
Yes - Verifying communication
No - Not OK
-------------------------------------------------
Battery voltage
The battery voltage is too low for continued use.
Replace with a fully charged battery.
It is recommended that a battery charger is connected to the vehicle for the whole download sequence.
Do you want to make a new attempt?
Yes - Checking battery voltage
No - Not OK
-------------------------------------------------