Infotainment Levels Upgrading

Infotainment levels upgrading

INTRODUCTION
- NOTE! Read through the whole installation instruction before starting the work.
- The illustrations display the procedure in order of operation. The order of operation is repeated in the text

Infotainment levels upgrading

Note! CD-player, CD-changer. This accessory is connected to the car's electrical system and requires vehicle-unique software.

Applies to cars up to model year -07

- Turn the ignition switch to position 0.
- Remove the ignition key from the ignition switch.

Note! Wait at least five minutes before disassembling the connectors or removing other electrical equipment.

Detach the panel at the rear edge of the centre console:
- Use a plastic weatherstrip tool to pry loose the panel. The panel is secured by a catch on each short side.
- Move the panel to the side to access the two screws underneath.

- Remove the two screws holding the centre console at the rear edge.

Remove the panel on the rear of the centre console:
- Open the glovebox.
- Use a plastic weatherstrip tool carefully to pry loose the panel. The panel is secured by a catch on each long side.
- Pull the panel downwards.

Remove the surround around the display and media player:
- Use a small screwdriver and press in the catches at one of the surround's upper corners. Carefully prize the surround away on one side using a plastic weatherstrip tool.
- Repeat the procedure for the other side and then fold the surround backwards into the vehicle. Pull the surround up until it detaches.

Hint: If there is difficulty removing the surround, press the panel back into place on both sides and start the removal procedure again. Start from the opposite side to before.

- Press out the display module from the reverse of the centre console. Press straight backwards, using both hands.
- Disconnect the two connectors. Put the display to one side.

- Remove the two screws holding the centre console to the dashboard.
- Remove the connector on the reverse of the dashboard environment panel.
- Remove the center console from the dashboard and tunnel console.

- Remove the two clips securing the cables to the media player by first pressing them to the sides and then pulling them away downwards.

Note! Be careful with the optic cables so that they are not bent or stretched.

Illustration A

- Remove the two screws in the lower edge of the existing media player. Save the screws, they shall be re-used.
- Pull out the media player and detach the connectors on the rear side.

Note! Make a mental note of how the cables are routed on the rear side.

- Put the media player to one side. It shall not be re-used.

Illustration B

- Take the new media player from the kit, and the two existing screws.

Note! Make sure that the fibre optic cable is routed so that it is bent to a radius of no less than 25 mm (1").

Plug in the connectors to the media player.
- Position the media player in the dashboard. Guide in the lug (1) at the rear edge of the media player using one hand. The lug must be in the corresponding hole on the reverse of the heater.
- Tighten the media player using the two screws.
- Reinstall the clips with the cables on the underside of the media player.

Reinstall:
- connector for the dashboard environment panel
- the centre console for the dashboard and tunnel console
- the connectors for the display
- the display
- the surround around the display and media player
- the panel on the rear of the centre console
- the panel at the rear edge of the centre console.
- Program the software in accordance with the service information in VIDA.

For cars from model year 08-

- Turn the ignition switch to position 0.
- Disconnect the battery negative lead.

Note! Wait at least three minutes before unplugging the connectors or removing other electrical equipment.

- Open the glovebox.
- Carefully pry off the panel inside the centre console. Use a plastic weatherstrip tool. The panel is secured by two clips on each of the short sides.
- Pull the panel away downwards.

- Remove the rubber mat and storage compartment.

- Detach the surround around the display and the media player by pressing in the catch at the edge of the media player cover. Use a small screwdriver. Carefully pry off the surround at the corner. Use a plastic weatherstrip tool.

Note! Do not damage the panel and dashboard.

- Repeat the operation on the other side.

Hint: If the other side does not detach, press the detached side into position again and repeat the procedure, beginning from the other side.

- Fold the surround backwards. Remove by pulling upwards.

- Press out the display module from the reverse of the center console. Use both hands and press straight back.
- Disconnect the two connectors. Put the display to one side.

- Carefully pry loose and remove the hand brake lever's panel.

Applies to cars with manual gearbox

- Remove the gear selector lever boot from the center console. First pry it off at the front edge using a weatherstrip tool and then unhook it at the rear edge.

- Loosen the gearshift knob from the shift by pressing down the knob and turning it slight more than a 1/4 turn anticlockwise and pull it up.

Applies to all models

Applies to the C70

- Remove the rear seat cushion by first pressing the outer edges of the cushion backwards and then by pulling them upwards so that the outer hooks release.

- Lift the cushion straight up in the middle so that the inner hooks release.

- Remove the rear cup holder from the rear tunnel compartment by prying at the leading edge and pressing in the catches, first at the leading edge and then on the sides.

- Remove the screws.

- Remove the rear tunnel compartment by pulling it upward (1) rearward (2) so that it releases from its catches.

Applies to all models

- Remove the two screws along the front edge of the tunnel console.

Illustrations A and B

- Carefully pull up the lock catch with special tool 9995919. At the same time, slide the whole tunnel console backward so that the two rear screws in the centre console's panel can be accessed.

- Remove the two screws.

- Remove the two screws holding the centre console to the dashboard.
- Remove the connector on the reverse of the dashboard environment panel.
- Remove the centre console's panel from the dashboard and tunnel console.

- Remove the two clips securing the cables to the media player by first pressing them to the sides and then pulling them away downwards.

Note! Make sure that the optic cables are not bent or stretched. They may not be bent with a radius less than 25 mm (1").

- Remove the two screws from the bottom of the media player.
- Pull out the media player and unplug the connectors on the back. Lay it aside, new is included in the kit.

Illustrations A and B