Engine Installation
Engine Installation
Special Tools Required
- Universal lifting eyelet 07AAK-SNAA120
- Engine hanger adapter VSB02C000015*
- Engine support hanger, A and Reds AAR-T1256*
- Front subframe adapter VSB02C000016*
- Subframe alignment pin 070AG-SJAA10S
*: Available through the Acura Tool and Equipment Program
1. Install the engine mount brackets and the accessory brackets and tighten their bolts to the specified torque.
2. Raise the vehicle on the lift, and position the engine/transmission under the vehicle. Lower the vehicle, and attach the universal lifting eyelet (A) and the chain hoist to the engine, then lift the engine into position in the vehicle.
NOTE: Reinstall the mounting bolts and the support nuts in the sequence given in the following steps. Failure to follow this sequence may cause excessive noise and vibration, and reduce engine mount life.
3. Attach the engine hanger adapter (VSB02C000015) to the threaded hole in the cylinder head.
4. Install the engine support hanger (AAR-T1256), then attach the hook to the slotted hole in the engine hanger adapter. Tighten the wing nut (A) by hand to lift and support the engine/transmission.
5. Tighten the new upper transmission mount bracket mounting bolts to the specified torque.
6. Install the ground cables.
7. Remove the chain hoist.
M/T model
A/T model
8. Remove the universal lifting eyelet.
9. Install the side engine mount bracket (A), and tighten the new bolts (B), then tighten the bolt (C).
10. Install the ground cable (D).
11. Raise the vehicle on the lift.
12. Support the front subframe (A) with the front subframe adapter (VSB02C000016). Position the steering gearbox washers (B) on the front subframe, and raise the subframe up to body.
13. Loosely install the new front subframe mounting bolts (C), the rear stiffener mounting bolts (D), the front stiffener mounting bolts (E), and the stiffeners (F).
14. Install the subframe middle mount (A), then loosely tighten the new subframe middle mount mounting bolts (B).
15. Remove the jack and the front subframe adapter.
16. Insert the subframe alignment pin (070AG-SJAA10S) through the positioning slot (A) on the right rear stiffener, through the positioning hole (B) on the subframe, and into the positioning hole (C) on the body, then loosely tighten the subframe right rear mounting bolt.
17. Insert the subframe alignment pin through the positioning slot on the left rear stiffener, through the positioning hole on the subframe, and into the positioning hole on the body, then loosely tighten the subframe left rear mounting bolt.
18. With the subframe alignment pin in place, tighten the subframe right rear mounting bolt.
19. With the subframe alignment pin in place, tighten the subframe left rear mounting bolt.
20. Tighten the stiffener mounting bolts to the specified torque.
21. Tighten the front and rear subframe mounting bolts to the specified torque.
22. Check that the positioning slots on the right/left rear stiffener, the positioning holes on the subframe, and the positioning holes on the body are aligned using the subframe alignment pin.
23. Tighten the bolts securing the subframe middle mounts.
24. '09 model: Install the ground cable (A) to the front subframe.
25. '10 model: Connect the ground cable connector at the front of the front subframe.
26. Tighten the nuts securing the lower transmission mount.
27. Lower the vehicle on the lift.
28. Remove the engine support hanger and the engine hanger adapter.
29. Tighten the new front engine mount bolt (A), then install the front engine mount stop (B), and connect the vacuum hose (C).
30. A/T model: Install the automatic transmission fluid (ATF) cooler line mounting bolts (D).
31. M/T model: Install the rear engine mount (A), then tighten the new rear engine mount mounting bolts in the numbered sequence shown.
32. A/T model: Install the rear engine mount upper bracket (A). Install the rear engine mount (B), then tighten the new rear engine mount mounting bolts in the numbered sequence shown.
33. Loosen the mounting bolts for the side engine mount bracket, then retighten the bolts.
34. Loosen the mounting bolts for the upper transmission mount bracket, then retighten the bolts.
M/T model
A/T model
35. Make sure the steering gearbox washers are set securely. Tighten the steering gearbox mounting bolts.
36. Raise the vehicle on the lift.
37. Install a new set ring on the end of each driveshaft, then install the driveshafts. Make sure each ring "clicks" into place in the differential and the intermediate shaft.
38. Connect the lower arms to the knuckles. Front Lower Arm Removal/Installation
39. Install the damper fork. Front Lower Arm Removal/Installation
40. A/T model: Install the shift cable. Service and Repair
41. Install exhaust pipe A. Use new gaskets (B) and new self locking nuts (C).
42. Install the A/C compressor (A), then connect the A/C compressor clutch connector (B).
43. Install the splash shield.
44. Install the front wheels.
45. Lower the vehicle on the lift.
46. Install the drive belt. Drive Belt Removal/Installation
47. A/T model: Install the ATF cooler hoses (A) to the transmission, and secure the hoses with the clips (B). Service and Repair
48. Connect the upper radiator hose (A) and the heater hoses (B).
49. Check the quick connector (A) and set ring (B) for cracks or damage. If the connector and/or set ring are cracked or damaged, replace the connector.
50. Make sure the set ring is in place inside the quick connector. If the set ring is off the connector, replace the quick connector.
51. Install a new O-ring (C) in the quick connector.
52. Check the lock (D). If the lock is damaged or deformed, replace it. When installing the new lock on the connector, push it straight down along the groove.
53. Clean the connecting surface of the thermostat cover (E), then apply clean engine coolant around the connecting surface.
54. Push the lock (A) down, then push the quick connector (B) onto the thermostat cover until you hear it click.
55. M/T model: Install the clutch slave cylinder, and the clutch line bracket mounting bolt. Manual Transmission Installation
56. M/T model: Install the shift cable. Manual Transmission Installation
57. Install the ignition coil cover (A) and the brake booster vacuum line mounting bolts (B).
58. Connect the fuel feed hose (A) Fuel Line/Quick-Connect Fitting Installation, then install the quick-connect fitting cover (B).
59. Install the evaporative emission (EVAP) canister hose (A) and the brake booster vacuum hose (B).
60. Connect the engine wire harness connector (A).
61. Install the starter subharness connector (B) to the bracket, then connect the connector.
62. Install the harness clamps (C).
63. Install the battery cables (D) to the under-hood fuse/relay box.
64. Install the engine control module (ECM)/powertrain control module (PCM) bracket assembly (A).
65. Connect the ECM/PCM connectors (B).
66. Install the harness clamps (C).
67. Install the strut brace. Frame Brace Replacement
68. Install the air cleaner assembly. Service and Repair
69. Do the battery installation procedure. Removal and Replacement
70. Inspect for fuel leaks. Turn the ignition switch to ON (II) (do not operate the starter) so the fuel pump runs for about 2 seconds and pressurizes the fuel line. Repeat this operation three times, then check for fuel leakage at any point in the fuel line.
71. Refill the engine with recommended engine oil. Service and Repair
72. Refill the transmission with fluid:
- Manual transmission Service and Repair
- Automatic transmission ATF Replacement
73. A/T model: Move the shift lever to each gear, and verify that the A/T gear position indicator follows the transmission range switch.
74. M/T model: Check that the transmission shifts into all gear smoothly.
75. Refill the radiator with engine coolant, and bleed the air from the cooling system with the heater valve open. Service and Repair
76. Check for fluid leaks.
77. Do the ECM/PCM reset procedure. Initial Inspection and Diagnostic Overview
78. Do the crankshaft position (CKP) pattern clear/CKP pattern learn procedure. Initial Inspection and Diagnostic Overview
79. Inspect the idle speed. Testing and Inspection
80. Inspect the ignition timing. Testing and Inspection
81. Check the wheel alignment. Service and Repair
