Courtesy Lamps Malfunction
Courtesy Lamps Malfunction
Diagnostic Instructions
* Perform the Diagnostic System Check - Vehicle (Initial Inspection and Diagnostic Overview) prior to using this diagnostic procedure.
* Review Strategy Based Diagnosis (Initial Inspection and Diagnostic Overview) for an overview of the diagnostic approach.
* Diagnostic Procedure Instructions (Initial Inspection and Diagnostic Overview) provides an overview of each diagnostic category.
Diagnostic Fault Information
Circuit/System Description
The INTERIOR LIGHTS fuse supplies battery voltage to the body control module (BCM). The BCM applies battery voltage to the courtesy lamps through the courtesy lamp supply voltage circuit. When any door is opened, the jam switch contacts close and the BCM receives a door-open input. If the BCM receives a door lock or unlock input or a rear hatch open input, the BCM will activate the courtesy lamp supply voltage circuit, providing battery voltage to all of the instrument panel (I/P) courtesy lamps, rearview mirror lamps, and rear compartment lamps. The courtesy lamps can be manually activated by placing the interior lamp switch in the DOME position. The BCM also provides a serial data message to the driver door module (DDM) and passenger door module (PDM) to apply battery voltage to the courtesy lamps located on each door.
Reference Information
Schematic Reference
Interior Lights Schematics (Interior Lights Schematics)
Connector End View Reference
Component Connector End Views (Connector Views)
Description and Operation
Interior Lighting Systems Description and Operation (Interior Lighting Systems Description and Operation)
Electrical Information Reference
* Circuit Testing (Component Tests and General Diagnostics)
* Connector Repairs (Component Tests and General Diagnostics)
* Testing for Intermittent Conditions and Poor Connections (Component Tests and General Diagnostics)
* Wiring Repairs (Component Tests and General Diagnostics)
Scan Tool Reference
Control Module References (Programming and Relearning) for scan tool information
Circuit/System Verification
1. Ignition ON, observe the scan tool Dome Lamp Switch parameter while pressing and releasing the dome lamp switch. The reading should toggle between Off and On.
• If the reading does not change between the commanded states, refer to Dome Lamp Switch Malfunction.
2. Observe the scan tool LF Door Open Switch parameter while opening and closing the driver door. The reading should toggle between Door Open and Key Off.
• If the reading does not change between the commanded states, refer to Door Open Switch Malfunction.
3. Observe the scan tool RF Door Open Switch parameter while opening and closing the passenger door. The reading should toggle between Door Open and Key Off.
• If the reading does not change between the commanded states, refer to Door Open Switch Malfunction.
Circuit/System Testing
Console Courtesy Lamp Malfunction
1. Ignition OFF, disconnect the harness connector at the console courtesy lamp.
2. Ignition OFF, console open, verify that a test lamp illuminates between B+ and the ground circuit terminal B.
• If the test lamp does not illuminate, test the ground circuit for an open/high resistance, if the circuit tests normal, replace the console lamp switch.
3. Ignition ON, verify that a test lamp illuminates between the control circuit terminal A and ground.
• If the test lamp does not illuminate, test the control circuit for a short to ground or an open/high resistance. If the circuit tests normal, replace the BCM.
4. If all circuits test normal, replace the console courtesy lamp.
Dome Lamp Switch Malfunction
1. Ignition OFF, disconnect the harness connector at the driver information center (DIC) switch.
2. Ignition OFF, verify that a test lamp illuminates between B+ and the ground circuit terminal 7.
• If the test lamp does not illuminate, test the ground circuit for an open/high resistance. If the circuit tests normal, replace the IPC.
3. Ignition ON, verify the scan tool Dome Lamp Switch parameter is Off.
• If not the specified value, test the signal circuit terminal 4 for a short to ground. If the circuit tests normal, replace the IPC.
4. Install a 3A fused jumper wire between the signal circuit terminal 4 and ground. Verify the scan tool Dome Lamp Switch parameter is On.
• If not the specified value, test the signal circuit for a short to voltage or an open/high resistance. If the circuit tests normal, replace the IPC.
5. If all circuits test normal, test or replace the DIC switch.
Door Courtesy Lamps Malfunction
1. Ignition OFF, disconnect the harness connector at the inoperative door courtesy lamp.
2. Ignition OFF, verify that a test lamp illuminates between B+ and the ground circuit terminal 2.
• If the test lamp does not illuminate, test the ground circuit for an open/high resistance.
3. Connect a test lamp between the control circuit terminal 1 and the ground circuit terminal 2.
4. Command the inoperative Door Exterior Courtesy Lamp ON and OFF with a scan tool. The test lamp should turn ON and OFF when changing between the commanded states.
• If the test lamp is always ON, test the control circuit for a short to voltage. If the circuit tests normal, replace the appropriate door control module.
• If the test lamp is always OFF, test the control circuit for a short to ground or an open/high resistance. If the circuit tests normal, replace the appropriate door control module.
5. If all circuits test normal, replace the inoperative door courtesy lamp.
Door Open Switch Malfunction
1. Ignition OFF, disconnect the harness connector at the inoperative door latch assembly.
2. Ignition OFF, interior lamps OFF, doors CLOSED, test for less than 5 ohms between the appropriate ground circuit terminal listed below and ground.
* Driver door latch ground terminal 8
* Passenger door latch ground terminal 3
• If greater than the specified range, test the ground circuit for an open/high resistance.
3. Ignition ON, verify the scan tool Door Open Switch parameter is Key Off.
• If not the specified value, test the appropriate signal circuit terminal listed below for a short to ground. If the circuit tests normal, replace the BCM.
* Driver door open switch signal terminal 7
* Passenger door open switch signal terminal 2
4. Install a 3A fused jumper wire between the appropriate signal circuit terminal listed below and ground. Verify the scan tool Door Open Switch parameter is Door Open.
* Driver door open switch signal terminal 7
* Passenger door open switch signal terminal 2
• If not the specified value, test the signal circuit for a short to voltage or an open/high resistance. If the circuit tests normal, replace the BCM.
5. If all circuits test normal, test or replace the inoperative door latch assembly.
Instrument Panel (I/P) Compartment Lamp Malfunction
1. Ignition OFF, disconnect the harness connector at the I/P compartment lamp.
2. Ignition OFF, scan tool OFF, interior lamps OFF, test for less than 1 ohm between the ground circuit terminal B and ground.
• If greater than the specified range, test the ground circuit for an open/high resistance.
3. Ignition ON, verify that a test lamp illuminates between the control circuit terminal A and ground.
• If the test lamp does not illuminate, test the control circuit for a short to ground or an open/high resistance. If the circuit tests normal, replace the BCM.
4. If all circuits test normal, replace the I/P compartment lamp switch.
Instrument Panel Courtesy Lamps Malfunction
1. Ignition OFF, disconnect the harness connector at the inoperative courtesy lamp.
2. Ignition OFF, test for less than 1 ohm between the control circuit terminal B and ground.
• If greater than the specified range, test the control circuit for a short to voltage or an open/high resistance. If the circuit tests normal, replace the BCM.
3. Ignition ON, verify that a test lamp illuminates between the control circuit terminal A and ground.
• If the test lamp does not illuminate, test the control circuit for a short to ground or an open/high resistance. If the circuit tests normal, replace the BCM.
4. Ignition OFF, connect a test lamp between the control circuit terminal A and the control circuit terminal B.
5. Command the Interior Lamps ON with a scan tool. The test lamp should turn ON for 5 seconds and then turn OFF.
• If the test lamp remains ON at all times, test the control circuit terminal B for a short to ground. If the circuits test normal, replace the BCM.
6. If all circuits test normal, replace the inoperative courtesy lamp.
Rear Compartment Courtesy Lamps Malfunction
1. Ignition OFF, disconnect the harness connector at the inoperative rear compartment lamp.
2. Ignition OFF, exterior lamps OFF, rear compartment lid open, test for less than 5 ohms between the ground circuit terminal B and ground.
• If greater than the specified range, test the ground circuit for an open/high resistance, if the circuits test normal, replace the rear compartment lid pull down actuator.
3. Ignition ON, verify that a test lamp illuminates between the control circuit terminal A and ground.
• If the test lamp does not illuminate, test the control circuit for a short to ground or an open/high resistance. If the circuit tests normal, replace the BCM.
4. If all circuits test normal, replace the inoperative rear compartment lamp.
Underhood Lamp Malfunction
1. Ignition OFF, disconnect the harness connector at the underhood lamp.
2. Ignition OFF, test for less than 5 ohms between the ground circuit terminal B and ground.
• If greater than the specified range, test the ground circuit for an open/high resistance.
3. Ignition ON, verify that a test lamp illuminates between the control circuit terminal A and ground.
• If the test lamp does not illuminate, test the control circuit for a short to ground or an open/high resistance. If the circuit tests normal, replace the BCM.
4. If all circuits test normal, replace the underhood lamp.
Vanity Mirror Lamps Malfunction
1. Ignition OFF, disconnect the harness connector at the inoperative vanity mirror.
2. Ignition OFF, scan tool OFF, interior lamps OFF, test for less than 1 ohm between the ground circuit terminal B and ground.
• If greater than the specified range, test the ground circuit for an open/high resistance.
3. Ignition ON, verify that a test lamp illuminates between the control circuit terminal A and ground.
• If the test lamp does not illuminate, test the control circuit for a short to ground or an open/high resistance. If the circuit tests normal, replace the BCM.
4. If all circuits test normal, replace the inoperative vanity mirror.
Repair Instructions
Perform the Diagnostic Repair Verification (Verification Tests) after completing the diagnostic procedure.
* Door Lock Replacement (Door Lock Replacement)
* Rear Compartment Lid Latch Replacement (Service and Repair)
* Driver Information Display Switch Replacement (Service and Repair)
* Sunshade Replacement (Service and Repair)
* Cargo Lamp Replacement (Cargo Lamp Replacement)
* Underhood Lamp Replacement (Service and Repair)
* Console Replacement (Service and Repair)
* Door Trim Panel Replacement (Service and Repair)
* Control Module References (Programming and Relearning) for BCM, DDM, IPC, or PDM replacement, setup, and programming